Decks · Care

Deck Maintenance: Cleaning, Staining and Common Problems Solved

Decks have a reputation for endless upkeep. They don't really need it - the small jobs just have to happen. A good clean each spring, leaves cleared in fall and a fresh coat of stain or sealer every couple of years are the difference between a deck that looks good at fifteen and one that is gray, green, splintery and soft at seven. Here is the whole routine, adjusted for where you live.

General guidance for American homeowners. Always follow the label on any cleaner, stain or power tool, test on a hidden spot first, and keep run-off away from plants, storm drains and waterways. Part of the PlantMapper Decking section.

Dry fall leaves scattered across wood deck boards
Leaves left to sit are what turn a deck green · photograph via Pexels
The honest picture

A few hours a year, at the right moments

Almost every deck complaint - it went green, it got slippery, it started splintering, the color washed out - traces back to the same thing. Not a bad board or a bad build, but a deck that was stained in year one and then forgotten.

The routine that keeps a deck in good shape is short: a proper clean in spring, leaves cleared through fall, and a coat of stain or sealer when the wood starts soaking up water instead of shedding it. Composite and PVC need the cleaning and nothing else.

The fall cleanup is the one people skip and the one that matters most. A deck that goes into winter clean and clear - whether that means snow in Minnesota or months of rain in Oregon - comes out in decent shape. One that goes in under a mat of wet leaves comes out green, slippery and a much bigger job.

The whole regime

A deck through the year

The complete maintenance schedule, timed to your own climate rather than a calendar. There is nothing else.

The year-round routine for a backyard deck. Timing shifts with your zone: spring work starts around your last frost (March in zones 7-8, May in zones 3-4), and in frost-free areas of the Deep South, Florida and Southern California it can happen whenever there is a dry spell. Composite and PVC need the cleaning entries only - skip everything involving stain or sealer.
WhenWhat to doHow long
Early spring (around your last frost)The main job: sweep, clean the whole deck with an oxygen-bleach deck cleaner, clear the gaps between boards, rinse and let it dryTwo to three hours
Spring, once dryCheck screws and nails, re-drive anything raised, look for soft or split boards, and check the ledger, flashing, posts and stairs underneath30 minutes
Late springRe-stain or re-seal if the wood needs it - see the water test below. Pick two or three dry days with temperatures roughly 50-90°FHalf a day
SummerSweep occasionally; move furniture and planters so the deck weathers evenly; wipe up grill grease and spills promptlyMinutes
Fall (as the leaves drop)The important one. Keep leaves blown or swept off, and give the deck a quick wash before winterAn hour, repeated
Late fallClear the gaps between boards, check gutters and downspouts aren't dumping water on the deck, raise planters off the surface30 minutes
WinterIn snowy zones, clear snow with a plastic shovel along the boards and use only the ice melt your board maker approves. Don't stain in cold, damp weatherMinutes
Every 2-3 yearsFull clean, brighten and re-stain for pressure-treated and cedar; ipe oiled every year or two if you want to keep the colorA weekend

The water test tells you when to recoat. Sprinkle a cup of water on a few different parts of the deck. If it beads up, the finish is still working and you can leave it. If it soaks straight in and darkens the wood, the protection is gone and it is time to clean and re-coat. That is far more reliable than a calendar, because boards in full afternoon sun - especially in the South and the high-altitude West - wear out long before shaded ones.

The main job

Cleaning a deck properly

Most decks need nothing dramatic. A stiff brush, the right cleaner and a little patience will bring back a surface people assume is beyond saving.

  1. Clear everything off and sweep

    Furniture, planters, the grill, the lot. Sweep the whole surface, then run a putty knife or a deck gap tool along every gap between the boards. The packed debris in those gaps holds moisture against the board edges and stops the deck draining.

  2. Wet the deck and nearby plants

    Wetting the boards first stops the cleaner soaking in unevenly and drying in patches. Wetting nearby shrubs and flower beds, and covering anything precious, protects them from splashes.

  3. Use a real deck cleaner

    Use an oxygen-bleach (sodium percarbonate) deck cleaner rather than chlorine bleach or dish soap. Chlorine bleach strips color, breaks down wood fibers and harms plants; dish soap leaves a film that stops stain soaking in. Work in manageable sections and don't let the cleaner dry on the surface.

  4. Scrub along the grain

    A stiff-bristled deck brush on a pole, working along the length of the boards. Along the grain lifts dirt out of the wood; across it drives dirt in and raises the fibers.

  5. Rinse, then brighten

    A garden hose is usually enough. Rinse until the water runs clear, rinse surrounding plants and paving too, and on wood decks follow with an oxalic-acid deck brightener, which restores the color and gets the wood ready to take stain.

  6. Let it dry completely

    Two or three dry days before applying any stain or sealer, longer in humid weather. Wood that looks dry on top can still be wet inside, and a coating applied over damp wood won't soak in and will peel.

Handle with care

Power washing - useful, and easy to overdo

A power washer cleans a deck in a fraction of the time. It can also wreck one just as fast if it is used carelessly, and the damage is permanent.

✓If you do use one

  • Use a 25- or 40-degree fan tip, never the red 0-degree tip or a turbo nozzle.
  • Keep the pressure low - roughly 500-1,200 psi for softer woods like pressure-treated pine and cedar, and lower still if the wood is old.
  • Hold the wand at least 12 in from the surface and keep it moving constantly.
  • Work along the grain, one board at a time, from one end to the other.
  • Test on a hidden corner first, and look closely at the result before continuing.
  • Expect to sand lightly afterwards - power washing raises the grain even when done well.

!Why it often goes wrong

  • It gouges soft wood. Too close or too much pressure carves tracks that never come out, especially in cedar and redwood.
  • It raises and tears the fibers, which is what produces splinters a year later.
  • It drives water deep into the wood, so the deck needs far longer to dry before staining.
  • It strips old stain unevenly, leaving a blotchy finish that has to be fully removed.
  • It can force water into the frame through the board gaps and behind the ledger.
  • On composite and PVC it can void the warranty - check the manufacturer before you point one at it.

For most decks, a brush is genuinely better. A stiff deck brush, an oxygen-bleach cleaner and twenty minutes per section will lift mildew and grime as well as a power washer, without raising the grain, gouging the boards or soaking the wood. Save the power washer for a badly neglected deck you are about to sand and refinish anyway.

What to put on it

Sealer, stain, solid stain or nothing

Four honest options for wood decks, each suited to a different attitude. Composite and PVC need none of them - skip to the composite section below.

Clear water sealer

The simplest option. A clear or lightly toned penetrating sealer soaks into the wood rather than forming a film, so it repels water, lets the grain show and never peels.

  • What it does Repels water; reduces checking, cupping and raised grain; keeps the natural color for a while
  • Frequency Every year on exposed decks - clear finishes wear fastest in strong sun
  • Advantage It wears away rather than peeling, so re-coating means a clean and another coat - no stripping or sanding
  • Watch out for Little or no UV protection, so the wood still grays. A toned or transparent stain is the compromise

Semi-transparent stain

Pigmented, so much better at resisting the sun. The pigment blocks UV, so the more color in the stain, the longer the wood holds its look - while the grain still shows through.

  • What it does Colors and protects; slows graying considerably; can change the look of a deck completely
  • Frequency Every two to three years, depending on sun exposure
  • Advantage The best color retention of the penetrating finishes, and a wide choice of tones; the most popular choice for pressure-treated and cedar decks
  • Watch out for Cheap film-forming finishes can peel and then need stripping. Penetrating, oil-based or hybrid stains are far more forgiving on a deck

Solid stain

Opaque, like paint, and the right answer for some situations - but it is a commitment, because once a deck is solid-stained it is hard to go back to a see-through finish.

  • What it does Covers completely; hides tired or mismatched boards; gives strong color
  • Frequency Every three to five years on the floor, longer on railings, plus touch-ups
  • Advantage Excellent coverage on a deck that has seen better days, and good UV protection
  • Watch out for It forms a film, so it wears and peels on stairs and walkways, and re-coating means scraping and sanding the loose edges. It can be slippery when wet unless you add a non-slip additive. Thick "deck resurfacer" coatings promise to fix rotten boards - replacing the bad boards is the better fix

Leave it to silver

A legitimate choice, and a popular one with cedar and ipe. Unfinished wood weathers to an even silver-gray, which many people prefer to any stain.

  • What happens Color fades over one to three years to a soft gray. This is a surface effect, not rot
  • You still must Clean it every year. Graying is fine; mildew and algae are not, and leaving it dirty is what really shortens its life
  • Suits Ipe, cedar and redwood particularly well, plus coastal and modern homes
  • Watch out for Pressure-treated pine left completely bare checks, raises grain and splinters faster than a maintained deck. An occasional clear sealer is a sensible middle course

Cleaning and treating

Amazon picks

As an Amazon Associate, PlantMapper may earn from qualifying purchases. Prices and availability are set by Amazon. Test any cleaner or finish on a hidden board first, follow the label dilution and dwell times, and keep run-off away from plants, storm drains and waterways.

Doing it well

Applying stain or sealer

The most common reason a stain fails is not the product. It is that it went onto a deck that was damp, dirty or both.

  1. Let new wood dry out

    New pressure-treated lumber is often still wet from treatment and won't take a finish. Leave it a few weeks to a few months, until water soaks in rather than beading, then clean and stain. Kiln-dried-after-treatment (KDAT) lumber can be finished much sooner.

  2. Clean first, always

    Stain seals in whatever is underneath it. Applied over mildew or grime, it traps them and looks blotchy within a season.

  3. Pick the weather carefully

    Two or three dry days before and at least a day after. Avoid hot midday sun, which dries the surface before the stain soaks in, and skip it below about 50°F, above about 90°F, or when rain is forecast. In the humid Southeast, early morning dew means starting later in the day.

  4. Stir, don't shake

    Pigment settles. Stir well at the start and as you work, or the color will drift across the deck. If you are using more than one can, mix them together in a bucket first (called boxing) so the shade is consistent.

  5. Work one full board at a time, end to end

    A brush, a pad or a stain applicator on a pole, along the grain, taking each board from one end to the other without stopping. Stopping mid-board leaves a lap mark that will still show in two years.

  6. Thin coats, not one thick one

    Thin coats soak in; thick coats sit on the surface, stay tacky and peel. Many penetrating stains go on wet-on-wet - follow the label - and wipe up any puddles before they dry.

  7. Do the ends and edges

    Board ends and the cut edges around stairs soak up far more than the faces and are where rot starts. Give them an extra coat.

The short version

Looking after composite and PVC

Composite and PVC really are low maintenance, which is not the same as no maintenance. The whole routine is right here.

✓What composite and PVC need

  • A wash a couple of times a year with warm soapy water or the cleaner the manufacturer recommends, and a soft brush.
  • Leaves cleared in fall, exactly as for wood - leaf tannins stain uncapped boards.
  • Gaps kept clear so the deck drains.
  • Spills wiped promptly. Grease, wine and sunscreen can mark, especially on uncapped boards.
  • Pads under furniture and under anything that gets dragged.
  • Snow cleared with a plastic shovel, never a metal-edged one, and only the ice melt the manufacturer approves.

!What to keep away from it

  • Never stain, seal or paint it. It can't absorb them and the coating will peel.
  • Grills and fire pits directly on the surface - heat marks are permanent. Use a grill mat.
  • Metal shovels, wire brushes and scourers, which scratch the cap.
  • Harsh solvents and chlorine bleach unless the manufacturer specifically permits them.
  • High-pressure washing - many manufacturers void the warranty; check first, and if allowed use a wide fan tip at low pressure.
  • Rubber-backed mats left in place, which can discolor the surface beneath.
Diagnosis

Eight deck problems and what causes them

Almost everything that goes wrong with a deck shows up in this table.

Common deck problems, their usual cause and the practical fix. If a deck feels unsafe, a post or joist is soft, or the ledger is pulling away from the house, stop using it and have it inspected.
What you see or feelUsually meansWhat to do
Green film, slippery underfootAlgae or mildew, from a surface that stays damp - shade, poor airflow or leaves left to sitClean with an oxygen-bleach deck cleaner and a stiff brush; clear leaves in fall; open up airflow underneath; fit anti-slip strips on stairs
Black spots or streaks running down the boardsCorroding fasteners - interior or electro-galvanized screws in treated lumber - or tannins reacting with ironReplace the offending screws with coated or stainless deck screws; an oxalic-acid brightener lightens the stains, though they may not clear completely
Boards cupping into a shallow troughUneven moisture between the top and bottom faces, usually from poor ventilation or a deck built too close to the groundOpen up airflow under the deck; badly cupped boards can be flipped or replaced
Springy or bouncy underfootJoists too far apart or undersized, or a beam, post or ledger connection has moved or rottedInvestigate straight away. Add joists or blocking if spacing is the problem; if a member is soft or the ledger is loose, have it inspected
Splinters and rough, raised grainSun and weather on bare pressure-treated pine, often made worse by power washingSand along the grain with 60-80 grit, clean, then stain. Prevent it by keeping the wood finished
Boards splitting at the endsScrews too close to the end without pre-drilling, or the wood drying outPre-drill new screws; small checks can be left, badly split boards replaced
Round holes in cedar, or sawdust under railsCarpenter bees boring into bare softwood, or termites where wood touches soilPaint or stain bare wood to deter carpenter bees; for termite mud tubes or soft, hollow wood, call a licensed pest professional
Soft, spongy wood, especially at posts, ledger and board endsRot - wood has been in contact with damp soil or stayed wet, often above-ground lumber used where ground-contact was neededStructural. Probe with a screwdriver; if it sinks in, that member needs replacing and the cause fixed
Learn from other people

Six maintenance mistakes

1. Cleaning with chlorine bleach

It strips color, breaks down the wood fibers, harms nearby plants and leaves the surface poorly prepared for stain.

The fixUse an oxygen-bleach deck cleaner. It costs a few dollars more and does the job properly.

2. Power washing too close, too hard

A narrow tip held near soft wood carves permanent tracks and tears the fibers, which is what produces splinters the following year.

The fixWide fan tip, low pressure, at least 12 in away, moving constantly - or use a brush instead.

3. Staining a deck that is still damp

The stain can't soak in, so it sits on the surface, stays tacky and peels within months.

The fixTwo or three dry days first, and use the water test before you open the can.

4. Skipping the fall cleanup

Wet leaves left on a deck all winter rot down into a perfect bed for algae and mildew, which is what makes it slippery by spring.

The fixKeep clearing leaves as they fall, and give the deck a wash before winter sets in.

5. Leaving pots and furniture in the same place all year

The deck weathers unevenly and moisture is trapped underneath, leaving permanent marks and sometimes rot.

The fixMove pots and furniture a few times a year, and stand planters on feet or a caddy.

6. Ignoring a bouncy board or a loose railing

Springiness or a wobbly guard is the first sign of a structural problem, and it never improves on its own.

The fixInvestigate as soon as you notice it. Probe suspect wood with a screwdriver - if it sinks in, or the ledger or guard posts move, get the deck inspected.

Twice a year

The maintenance checklist

Twelve checks for the spring and fall sessions. Ticks are saved in this browser only.

Spring

Staining

Fall

Care questions

Deck maintenance: frequently asked questions

How do I stop my deck going green and slippery?

The green is algae or mildew, and it grows wherever the surface stays damp. Clean the deck with an oxygen-bleach deck cleaner and a stiff brush each spring, keep leaves cleared through fall, clean out the gaps between boards so water drains, and open up airflow underneath if you can. Fit anti-slip strips on the stairs whatever else you do - that is where falls happen.

Can I power wash my deck?

You can, but carefully. Use a 25- or 40-degree fan tip, keep the pressure low (roughly 500-1,200 psi for pressure-treated pine and cedar), hold the wand at least 12 in away, keep it moving and work along the grain. Held too close or set too high, it gouges the wood permanently and tears the fibers, which causes splinters later. For most decks a stiff brush and a deck cleaner is the better tool. Check the manufacturer before power washing composite or PVC - it can void the warranty.

How often should I stain or seal my deck?

Rather than following a calendar, use the water test: sprinkle water on several parts of the deck, and if it soaks straight in and darkens the wood the protection is gone. In practice that is about every year for a clear sealer, and every two to three years for a semi-transparent stain on a sunny deck. Shaded areas last longer than boards in full afternoon sun, so test in several places.

How long should I wait to stain a new pressure-treated deck?

Usually a few weeks to a few months. New pressure-treated lumber is often still wet from treatment, and stain applied to wet wood won't soak in or stick. Sprinkle some water on the boards: when it soaks in instead of beading, clean the deck and apply the first coat. Kiln-dried-after-treatment (KDAT) lumber can be stained much sooner, and new cedar or ipe should be cleaned and brightened before its first finish.

Should I use a clear sealer or a stain?

A clear sealer repels water and lets the grain show but offers little UV protection, so the wood still grays and it needs re-doing about every year. A semi-transparent stain contains pigment, which blocks UV, so it holds color much longer while the grain still shows. For most pressure-treated and cedar decks a penetrating semi-transparent stain is the best balance; avoid cheap film-forming finishes on a deck floor, because when they fail they have to be stripped.

Can I paint my deck or use solid stain?

Yes, and it can rescue a tired or mismatched deck. Be aware it is close to a one-way decision: paint and solid stain form a film, so they wear and peel on walkways and stairs, and re-coating means scraping and sanding the loose edges. Use a product made for deck floors, add a non-slip additive for wet weather, and prepare the surface thoroughly first.

How do I get rid of black stains on my deck?

If the streaks run down from each screw or nail, they come from corroding fasteners - almost always interior or electro-galvanized screws used in treated lumber - or from tannins reacting with iron. Replace them with coated or stainless deck screws, then use an oxalic-acid deck brightener to lighten the marks. Scattered black spotting not linked to fasteners is usually mildew, and an oxygen-bleach deck cleaner will lift it.

When should I replace a deck rather than repair it?

Individual damaged, split or cupped boards are a simple swap and no reason to replace a deck. What matters is the frame and its connection to the house. Probe the joists, beams, posts and ledger with a screwdriver - if it sinks in, that member is rotten. Isolated rot can be repaired, but widespread softness, a ledger pulling away from the house, wobbly guards or a deck that feels springy across large areas means it has reached the end of its life. Stop using it and have it inspected.

Where to go from here

The next steps