Ask a landscaper for the cheapest way to sharpen up a yard and most will say the same thing: fix the edges. A clean line where the lawn stops and the mulch begins makes the whole front yard look tended, and a solid edge keeps gravel off the lawn, turfgrass out of the beds and soil off the sidewalk. Before you buy anything, settle three things: where the edge goes, how it meets the mower, and what shape it follows.
General guidance for American yards. Call 811 a few days before you dig so buried utilities are marked, check HOA rules if you have them, and get advice where an edge is also holding back soil. Part of the PlantMapper Landscape Edging section.
One sharp line changes the look of the whole yard · photograph via Pexels
Where to start
The best-value upgrade in landscaping
Drive down any street and you can pick out the yards with good edges. The beds look deliberate, the mulch stays where it was spread and the lawn ends in a line instead of a fuzzy mess. A bed melting into the grass, pea gravel scattered across the lawn, mulch washed onto the driveway after a thunderstorm: none of those are plant problems. They are edge problems, and an edge costs a few dollars a foot.
It helps to know which of three jobs you are paying for. Edging defines a line so the yard looks finished, it contains loose material such as gravel, mulch or soil, and occasionally it retains a small change in grade. Most products handle the first two well. Very few handle the third, and treating a decorative edge as a retaining wall is where most failures start.
This guide is about the decisions you make before buying: where an edge is worth having, what suits each spot, straight or curved, and how its height relates to the mower. Products are compared in Edging Materials and installation is covered in Installing Edging.
The honest test
Where edging is worth it, and where it isn't
An edge is cheap, but an unnecessary one is another line to trim around and another thing to trip over. Look at both lists before you buy.
✓Worth edging
Lawn meeting a flower bed. The classic job. It keeps grass out of the bed and mulch off the lawn, and ends the chore of recutting the line with a spade every few weeks.
Anything holding loose material. Pea gravel, crushed stone, decomposed granite, wood mulch and pine straw all drift without a firm edge.
Walkways through planting. A path with no edge gets a little narrower every season as the beds spill over it.
Small grade changes of 2 to 6 inches, such as a bed sitting slightly above the lawn or a path a little below a bed.
Vegetable and raised beds, where the edge is also the frame.
Long, gentle curves you want to keep. Without an edge, a few years of mowing slowly straightens a curve out.
!Usually not worth edging
Bed meeting bed. Two planted areas side by side don't need a line drawn between them.
Where a low hedge or dense planting already holds the line. Boxwood, liriope, lavender or a mown strip does it for free.
Native meadow and pollinator plantings, where a hard edge fights the look. A mown path through taller grasses suits them better.
Across a route people walk. An edge crossing a path is a trip line, however low it is.
Around every tree, rock and birdbath. Edging everything chops a small yard into pieces and makes it look like a commercial landscape.
Where the real job is retaining. Holding back more than about 6 inches of soil calls for a proper low wall; see Landscape Timber Projects.
The quick test. Stand where you normally see that part of the yard and ask what is actually going wrong. If grass is invading, gravel is escaping or soil is washing out, an edge fixes it. If the line just looks ragged, a half-moon edger or a sharp spade a couple of times a season fixes it for nothing, and a clean cut edge in good soil often looks better than cheap plastic edging ever will.
Five situations
What suits each location
What the edge is separating matters far more than personal taste.
Lawn to flower bed
It has to work with the mower
This is the most common edge in an American yard, and the one where the wrong choice adds work instead of saving it.
A flush mow strip of brick, pavers or poured concrete curbing set level with the soil is the gold standard; the mower wheel rides on it
Steel or aluminum set flush is the nearly invisible option and follows curves well
Avoid anything standing about 1 inch above the grass; it catches mower blades and toes
With Bermudagrass or zoysia, choose edging at least 4 to 6 inches deep, because their runners travel both over and under the soil
Or simply cut it with a half-moon edger a few times a season, which is free and looks sharp
Walkway or driveway to planting
Holding the surface comes first
A walkway edge stops the surface spreading and stops the beds stealing width. It usually needs to be tougher than a lawn edge, because wheelbarrows, trash cans and snow shovels hit it.
Concrete, pavers or brick backed with concrete for anything a wheelbarrow or car rolls over
Steel edging for gravel or decomposed granite paths, since it is thin and wastes no width
Keep a loose surface 1½ to 2 inches below the top of the edge so it stays put
In snow country, choose an edge that sits flush or is easy to see, so the shovel and snowblower don't catch it
Gravel to anything
Gravel always wants to wander
Loose stone finds every low spot and every gap. If you want a gravel area to keep its shape, edging is not optional.
The edge must stand 1½ to 2 inches above the finished gravel to hold it
Angular crushed stone stays put far better than round pea gravel, which escapes almost anything
Steel, aluminum, wood and pavers all work; thin plastic is usually too flimsy for the job
A raised bed edge is holding soil, so it is part of the structure rather than a decorative line.
Landscape timbers or 2x lumber for anything taller than about 6 inches; see Landscape Timber Projects
A board on edge held with stakes works for a simple 6-inch bed
Leave the bottom open so the bed drains into the ground below
Keep spans under about 6 feet or brace them, or wet soil will bow the sides out
Around trees
Go gently
A ring of edging around a tree is a common instinct and often a poor idea.
Never build a raised ring against the trunk and fill it with soil or a mulch volcano; it rots the bark
Keep any edge well away from the trunk, ideally out toward the drip line
Don't slice through roots when trenching; go around them
A simple wide mulch circle, 2 to 3 inches deep and pulled back from the trunk, is usually kinder and looks better
Wood set flush with the lawn lets the mower roll straight over itGravel stays put only when the edge stands above itA firm edge keeps loose, soft planting looking intentional
On paper
Straight runs or curves?
Decide the shape before the material, because the shape rules some products out completely.
✓Straight runs
Cheaper and faster. Little cutting, little waste.
Every material works, from wood boards and landscape timbers to brick, pavers, concrete and steel.
Suit formal yards, small lots and modern designs, where the geometry is the look.
Easier to keep true. A straight line is either straight or it isn't; a poor curve is harder to spot and harder to fix.
Make a narrow lot feel longer when they run the length of the yard.
Lay them out with stakes and a string line, and check the diagonals on any rectangle.
!Curves
Need a flexible material: steel, aluminum, plastic or composite strip, poured concrete curbing, or small units like bricks and pavers laid to the curve.
Wood boards won't curve without being cut into short straight pieces, which rarely looks right.
Make curves generous. A long, gentle sweep looks designed; a wobble looks like a mistake.
Lay them out with a garden hose and leave it there for a couple of days before you commit.
Cost more in materials and labor, often 20 to 40 percent more.
Suit cottage-style and naturalistic planting, and yards where you want to hide the far end.
Two rules that rescue most curved edges. First, use as few curves as you can: one generous sweep beats four small wiggles every time. Second, check the shape from an upstairs window or the deck. Curves that look convincing at ground level often look lumpy from above, and that is the view you see every day.
The detail that matters most
Finished height and the mower
More edging goes wrong on height than on material. Three-quarters of an inch in the wrong direction turns a work saver into a weekly nuisance.
Where the top of the edging should sit in each situation, measured against the surface beside it.
Situation
Set the edge…
Why
Lawn to bed, mower-friendly
Flush with the soil at the base of the grass, or about ¼ in below
The mower wheel rolls over it and cuts right to the line, so there is no string trimming and no recutting
Lawn to bed, raised line
Clearly above the lawn, 2 in or more
An obviously raised edge gets stepped and mowed around. It is the in-between height that catches things
Holding gravel or mulch
1½-2 in above the loose surface
Any lower and rain or foot traffic carries the material over the top
Walkway edge
Flush with the path, or slightly above on the planting side
Nothing should stick up across the line people walk or shovel
Bed sitting above a walkway
Top of the edge level with the bed soil, path 1½-2 in below
Keeps soil and mulch from washing onto the walk in a downpour
Raised bed
Soil about 2 in below the top of the frame
Stops soil and mulch spilling over every time you water
Decide how you will mow first
Where edging meets a lawn there are only two good answers: flush, so the mower rolls over it, or clearly raised, so everyone goes around. Anything roughly ½ to 1½ inches proud is the worst of both: it nicks blades, chips the edging, trips people and still needs string trimming.
Work down from the finished top
Fix where the top of the edge will sit, then work backward: edging depth, setting bed, crushed stone base. Building the base first and hoping it comes out right is how edges end up an inch too high.
Allow for settling and frost
New sod and freshly graded ground settle during the first year, so a mow strip set perfectly flush in spring can stand proud by the next. In colder zones, frost heave also pushes poorly anchored edging upward each winter. On new ground, a hair low is the safer mistake, and in frost country good anchoring matters as much as height.
Check the slope along the run
A long edge on sloping ground should either follow the grade or step down in even amounts. What looks wrong is an edge that stays dead level for 30 feet and then drops 3 inches all at once.
Water
Drainage: don't build a dam
An edge is a small wall, and a small wall across a slope holds back water. Most of the time it makes no difference. Now and then it makes a big one.
✓Keep water moving
Use a permeable edge across a slope, such as pavers or bricks with open joints or a gravel-filled channel, rather than solid concrete curbing.
Leave gaps in a solid edge that crosses the slope, or set it slightly low at one spot so water has a way through.
Keep grade sloping away from the house. Don't let an edge or raised bed trap water against the foundation or bury the siding.
On heavy clay, set edging on a crushed stone base rather than solid concrete so water doesn't sit underneath and freeze.
Watch where water runs in a heavy rain before you put a line across its route, and leave downspout outlets a clear path.
!Signs the edge is causing trouble
A new puddle since the edging went in, always on the uphill side.
Silt and mulch building up against one face after every storm.
Grass yellowing or dying in a strip along the edge.
Water running along the edge and dumping somewhere unhelpful, like a walkway, the driveway or a neighbor's yard.
Moss and algae on one side only.
If the ground stays wet whatever you do, the problem is bigger than the edge; see Yard Drainage.
Money and numbers
What edging costs, and how much to buy
Edging is sold by the linear foot, so budgeting is unusually easy. Measure the run, add 10 percent and multiply.
Very rough material costs per linear foot in the US. Planning figures only: prices vary a lot by region, supplier, product and quantity. Installation is extra.
Material
Rough material cost per foot
Notes
Plastic or vinyl strip
$1-3
The cheapest choice, and it tends to look it; prone to heaving
Pressure-treated wood board and stakes
$2-5
Cheap and easy; expect roughly 10 years
Composite edging
$3-6
Won't rot, holds a curve, needs nothing
Steel (powder-coated or weathering)
$3-8
The best-looking answer for curves; lasts for decades
Aluminum
$3-8
Lighter, won't rust, easier to handle; good near the coast
Precast concrete edging
$2-5
Cheap and tough, but straight runs only
Brick or pavers, set as a mow strip
$4-10
Handsome and doubles as a mow strip; a small masonry job
Natural stone
$8-20+
Cobbles, Belgian block or cut stone; the most attractive and most expensive
A contractor extrudes it in place; follows any curve
Professional installation of other types
$3-10 per foot extra
On top of materials; curves and masonry at the top end
Working out how much you need
Measure along the real line with a tape, or lay a hose on it and measure the hose, rather than scaling off a drawing;
curves are always longer than they look, often by 15 percent or more. Add 10
percent for cuts, overlaps and the piece that gets damaged. For bricks and pavers,
work out the number per foot first: a standard 8-inch brick laid end to end gives 1½ per foot,
and laid crosswise as a soldier course (about 2¼ in wide) gives roughly 5 per foot.
Price the bed as well as the edge
If you are edging a new flower bed, the free PlantMapper Flower Bed Cost Calculator gives you an honest price for the plants inside it before you head to the nursery.
The most common edging mistake of all. It is high enough to catch a mower blade and a toe, and low enough that nobody notices it.
The fixSet it flush so the mower rolls over it, or clearly raised so everyone goes around. Never in between.
2. Choosing wood boards for a curve
Lumber doesn't bend. Cutting it into short straight pieces gives a line that looks neither straight nor curved.
The fixUse steel, aluminum, composite or concrete curbing for curves, or redesign the line as straight runs.
3. Edging everything
A ring around every bed, tree and feature chops a small yard into pieces and makes it feel smaller and busier.
The fixEdge only where something is escaping or invading. Leave the rest.
4. Treating edging as a retaining wall
Most edging is made to hold a loose surface, not to resist the push of soil. Used as a retaining wall, it bows, leans and fails.
The fixAnything holding back more than about 6 inches of soil needs a proper low wall.
5. Damming the water
A solid edge across a slope stops the water that used to flow over it, and a new puddle appears on the uphill side.
The fixUse a permeable edge across a slope, or leave a gap for water to pass.
6. Measuring a curve off the drawing
A curved run is always longer on the ground than on paper, so people come up short and make a second trip to the home improvement store.
The fixLay a garden hose along the real line, measure it, then add 10 percent.
Planning questions
Planning edging: frequently asked questions
How high should landscape edging be?
It depends on the job. To hold in gravel or mulch, the edge should stand 1½ to 2 inches above the loose surface. Where it meets a lawn there are only two good heights: flush with the soil at the base of the grass so the mower rolls over it, or clearly raised by 2 inches or more so everyone goes around. Avoid roughly ½ to 1½ inches proud, which is high enough to catch mower blades and toes but low enough that nobody notices it.
Do I really need edging?
Only where something is going wrong. If grass is creeping into a bed, gravel is spilling onto the lawn or mulch is washing across a walkway, an edge fixes it cheaply and for good. If the line just looks ragged, a half-moon edger or sharp spade a couple of times a season gives a clean cut edge that costs nothing and often looks better than cheap plastic.
What is the best edging for a curved flower bed?
Steel or aluminum. Both come in flexible strips that bend into smooth curves, they are thin so they waste no bed space, and set flush they nearly disappear. Plastic or composite strip is cheaper, and poured concrete curbing is a popular installed option that follows any curve. Wood boards won't curve, and bricks or pavers can follow a curve but take longer and cost more.
How do I stop grass from growing into my flower beds?
Use a solid edge deep enough to block the runners. Edging buried 4 to 6 inches stops most lawn grasses. Bermudagrass and zoysia are the hardest, because they spread by runners above ground and rhizomes below, so use deeper edging and trim any runners that try to climb over the top. A spade-cut edge works too, but it needs recutting several times a season because it only removes runners instead of blocking them.
Should edging be level with the lawn?
If you want to save work, yes. An edge set flush with the soil, or about ¼ inch below, lets the mower wheel roll over it and cut right to the line, so there is no string trimming or recutting. New sod settles in its first year and frost can lift edging in cold zones, so on new ground set it very slightly low and anchor it well.
How much does landscape edging cost?
Very rough US figures that vary by region and supplier: plastic about $1 to $3 per linear foot, pressure-treated wood $2 to $5, steel and aluminum $3 to $8, brick and pavers $4 to $10, and natural stone more. Professionally installed concrete curbing commonly runs around $8 to $15 per foot. Measure the real line rather than scaling off a drawing, and add 10 percent.
Can edging hold back soil?
Only a little. Most edging is made to define a line and contain a loose surface, not to resist the sideways push of soil. Up to about 6 inches of grade change is usually fine with wood, steel or pavers on a firm base. Beyond that you are building a retaining wall, which needs a proper base, anchoring and drainage.
Will edging cause drainage problems?
It can, if a solid run crosses a slope and blocks water that used to flow across it. Signs are a new puddle on the uphill side, silt piling against one face or a strip of yellowing grass. Where an edge crosses a slope, use something permeable such as pavers with open joints, or leave a deliberate low spot so water has somewhere to go.