Patios · Problems

Patio Problems - What Went Wrong and How to Fix It

Pavers that sink or rock, corners lifted by frost, cracked or flaking concrete, joint sand that washes away, weeds, slimy algae, puddles that never drain and white bloom on brand-new pavers. Twenty common patio faults, what is really behind each one, how worried to be and the repair that will still be holding next year.

General guidance only. Anything involving your foundation, a retaining wall or water getting into the house needs someone to look at it in person. Part of the PlantMapper Patios section.

Cracked and uneven stone patio in dappled sunlight
Almost every patio fault comes back to water, a weak base or failing joints · photograph via Pexels
Where to start

Most patio trouble has one of three roots

A patio that has gone wrong can look like a dozen separate problems, but nearly all of them lead back to water that has nowhere to go, a base that has moved or joints that have stopped locking things together. And the three feed each other: open joints let rain into the bedding sand, wet sand and gravel soften or freeze, and a soft or heaving base lets pavers drop, tilt and spread.

Knowing that saves money. Sweeping fresh sand into a patio whose pavers are rocking is wasted effort, because the next storm or the next freeze will open the joints again. Scrubbing algae off a corner that never dries buys you one summer. Before you fix the thing you can see, ask what is causing it, and fix that if you can.

This page starts with a quick problem finder and an honest look at which faults are cosmetic and which are not, then works through twenty problems one by one, covering paver, flagstone and poured concrete patios. When a fault comes back to how the patio was built or drained, you will be pointed to Building a Patio or Patio Drainage; when the answer is a cleaning habit, to Patio Maintenance.

Jump straight there

Problem finder

Pick the thing you are looking at.

A quick sort. "Structural" means the fault is likely to get worse and may involve more than the surface.
What you seeMost likely causeHow urgentGo to
A paver or stone tips when you step on the edgeSoft spot or void in the bedding or baseFix soonRocking pavers
A mortared flagstone has broken freePoor bond to the mortar bed or slab belowFix soonLoose stones
A crack across a paver, stone or slabA load over an unsupported spot, or shrinkage in concreteFix soonCracks
A dip that gets deeper each yearBase or soil settling, often because of waterStructuralSunken areas
Mortar joints crumbling between flagstonesWeak mix, freeze-thaw or movement belowFix soonFailed joints
Grass and weeds in the jointsSeeds in debris on top of the joints, not roots from belowCosmeticWeeds
Slick green film when wetAlgae on surfaces that stay dampCosmetic, but a slip riskAlgae
Puddles still there hours laterToo little slope, or a few settled paversFix soonStanding water
Lifted corners after winter, or flaking concreteFrost heave, or freeze-thaw scaling made worse by saltPermanentFrost and de-icers
White chalky bloom on new paversEfflorescence: natural salts drying outNormalEfflorescence
Orange or brown spotsIron in the stone, or rust from furniture, grills or fertilizerCosmeticRust
Water in the basement near the patioPatio sloping toward the house, or set too high against itGet it checkedWhen to call a pro
A retaining wall bulging or leaningSaturated soil behind it, or a wall not built for the loadGet it checkedWhen to call a pro
Read this first

Which problems are minor and which are not

Most patio faults are a weekend job. A handful deserve a professional set of eyes right away.

Call a pro if you see any of these

!Water getting into the house

Damp basement walls, stains or musty smells on the side of the house next to the patio, or water running behind siding. The patio may slope toward the house or sit too high against it.

!A retaining wall on the move

Bulging, leaning, blocks sliding forward or cracks stepping through a wall. Wet soil behind a wall pushes extremely hard, and walls can fail without much warning.

!Cracks that keep growing

A crack that runs across the whole slab or several pavers, gets wider over months or has one side higher, especially near the house or a big tree.

!A dip that keeps sinking

Steady settlement suggests something is washing out or collapsing underneath, such as an old trench, a leaking pipe or buried debris.

!Water from nowhere

Wet patches in dry weather, or water bubbling up through joints, can mean a leaking irrigation line, water service or a spring.

!Steps that have shifted

One step taller or shorter than the rest trips people, and a step that has dropped often points to a bigger problem below.

Everything else on this page is a DIY-level job. These six are worth a contractor, structural engineer, foundation specialist or plumber looking at in person. If any repair means digging, call 811 first so buried utility lines are marked.

Group one

Sinking, heaving and settling

Faults where the surface, or what it sits on, has moved.

Rocking pavers and stones

Fix soon

What you notice. A paver or flagstone clunks or tips when you step on one edge, often with sand missing from the joints around it.

Likely causesA soft or hollow spot underneath. With pavers it is usually bedding sand that was laid too thick or unevenly, a base that was not compacted, or sand washed out through open joints. With mortar-set flagstone it is voids left by dabs of mortar instead of a full bed.

How seriousNot structural on its own, but it never stops by itself. Every rock grinds the joints open, more water gets in and the movement spreads.

RemedyPry the paver out, check the base under it is firm (tamp and add gravel if not), rescreed the roughly 1 in of bedding sand level with the neighbors, set the paver, tap it down with a rubber mallet and re-sand the joints. For flagstone, clean off the old mortar and reset on a full bed. Pounding it harder without lifting it does nothing.

PreventionEven bedding and a compacted base - see the bedding layer.

Loose flagstones and tiles

Fix soon

What you notice. A mortared flagstone or porcelain paver lifts out cleanly, sometimes with the mortar still stuck to the slab below instead of the stone.

Likely causesThe stone never bonded. Common with dense porcelain set without a bond coat, stone with a dusty back, mortar that had started to stiffen before the stone went down, or a concrete slab underneath that moves in frost.

How seriousA trip hazard more than a structural fault, but a warning: if one let go for that reason, others were probably set the same way.

RemedyChip off the old mortar, clean the back of the stone and the bed, apply a bonding slurry or thinset to the back of the stone, and reset on fresh mortar. Grout the joints once it has cured.

PreventionBond coat on dense stone and porcelain - see bonding.

Cracked pavers, stones and concrete

Fix soon

What you notice. A crack through a single paver or flagstone, or a line running across a concrete patio, sometimes with one side a little higher.

Likely causesFor pavers and stone, a heavy point load (grill, planter, ladder foot) over a soft spot. For poured concrete, drying shrinkage, control joints spaced too far apart, a poorly compacted base, frost heave or tree roots.

How seriousA single cracked paver is a nuisance. Hairline cracks in concrete are normal. A crack wider than about 1/4 in, with an offset or still widening, points to movement below.

RemedyReplace a cracked paver or stone and firm up the base while it is out, which is exactly why you keep a few spares from the original pallet. Seal narrow concrete cracks with a flexible concrete crack filler to keep water out; slabs with large offset cracks may need mudjacking, foam lifting or replacement.

PreventionSolid support under every unit, control joints in concrete about every 8 to 10 ft, and pads under heavy planters.

Uneven surface and trip edges

Trip hazard

What you notice. Neighboring pavers at different heights, so a chair leg catches or a toe snags. Usually worst along the outer edge or at a step.

Likely causesUneven settlement, missing or failed edge restraint letting the edge pavers spread and drop, roots lifting the surface, or pavers that were never set level in the first place.

How seriousCosmetic until someone falls. A lip of more than about 1/4 in on a walking route is worth fixing promptly.

RemedyLift the high or low pavers and relay them to a straightedge. Reinstall or add edge restraint spiked into the base. If roots are doing the lifting, decide about the tree before cutting anything big, and get an arborist's opinion for large trees.

PreventionEdge restraint on every open edge and a straightedge check as you lay.

Sunken areas

Structural

What you notice. A shallow bowl covering several pavers or part of a slab, usually holding water and slowly getting worse.

Likely causesThe base or the soil under it settling: gravel base too thin or not compacted in 2 to 3 in lifts, topsoil or roots left in place and rotting, sand and fines washing out, a backfilled utility or downspout trench, or soft clay that was paved over.

How seriousGenuinely structural. Relaying the surface without fixing what is under it usually buys a year or two.

RemedyLift the area, dig out the base, find the cause, then rebuild with compacted crushed stone (usually 4 to 6 in, more on clay or in cold regions) and relay. If water caused it, solve the water first. Sunken concrete slabs can sometimes be raised by mudjacking or polyurethane foam injection.

PreventionCompaction in thin layers on firm subgrade - see compaction.

Movement by a wall or retaining wall

Get it checked

What you notice. Pavers dropping or lifting along the house or a wall, a retaining wall leaning, or blocks pushing out behind a raised patio.

Likely causesWet soil behind a retaining wall with no drainage, backfill against the foundation that is still settling, or foundation movement.

How seriousPotentially very. Retaining walls tend to fail suddenly, and the forces behind them are large.

RemedySkip the cosmetic patch. Have a structural engineer or an experienced hardscape contractor look at it, and keep people and pets away from anything visibly leaning. Taller retaining walls often need a permit and engineering, so check locally.

PreventionDrainage behind walls and raised patios - see raised patios.

Group two

Joints, sand and weeds

The joints lock the patio together and keep water out of the base. Once they fail, the rest soon follows.

Crumbling mortar joints

Fix soon

What you notice. On a mortared flagstone or brick patio, the joints are turning sandy, breaking out in chunks or lifting out with a finger.

Likely causesA weak or sandy mix, dry mix brushed in and misted (which often never bonds properly), joints too narrow or shallow, mortar laid in cold weather or frozen while curing, freeze-thaw over many winters, or movement under the stones.

How seriousCosmetic at first, then not. Open joints let water under the stones, where it freezes and pushes them loose.

RemedyRake or grind out the loose mortar to full depth, clean and dampen the joint, and repoint with a mortar or a joint compound made for patios. Check that nothing rocks first - if it does, reset those stones before you repoint.

PreventionCorrect joint width and depth - see joints.

Joint sand washed out

Fix soon

What you notice. Empty joints between pavers, sand piled at the low edge of the patio, ants pushing sand up, and pavers starting to shift.

Likely causesOrdinary sand washed out by heavy rain or runoff from a downspout, blasted out by a pressure washer, carried off by ants, or joints never filled to the top in the first place.

How seriousMore than cosmetic. Without sand in the joints, pavers lose the side-to-side lock that holds the whole surface together.

RemedyClean out debris, check pavers are level, then sweep in fresh joint sand or polymeric sand, vibrate or tamp it down and top up again. Deal with the cause too: redirect a downspout that empties onto the patio, and change how you wash it.

PreventionGentle washing - see pressure washing.

Failed polymeric sand and haze

Fix soon

What you notice. Polymeric sand that has stayed soft, crumbled, washed out in patches or sunk in the joint, or a cloudy gray or white haze stuck on the paver faces.

Likely causesAlmost always the installation. Joints too shallow (most brands want at least 1 to 1.5 in of sand), pavers damp when the sand went on, rain soon after, not enough compaction, too much or too little water when activating it, or dust left on the surface that hardened into haze.

How seriousCosmetic, but it will not get better and it is tedious to redo.

RemedyRake out the failed sand (a pressure washer on a wide tip helps), let everything dry, then reinstall following the bag's instructions to the letter, on a dry day with no rain forecast. For haze, try a stiff brush and water first, then a polymeric haze remover. Most makers have customer help lines, so call before you start.

PreventionRead the whole bag before you open it, and blow the surface completely clean before wetting.

Weeds in the joints

Cosmetic

What you notice. Grass, crabgrass, dandelions, spurge and clover sprouting between pavers, worst along the edges and in shade.

Likely causesMostly a misunderstanding. Weeds in a patio rarely push up from the soil underneath; they sprout from seeds landing in the dust and debris that builds up in open joints. Full, firm joints give them nothing to grow in.

How seriousCosmetic, though roots left to grow can pry a weak joint wider.

RemedyPull them with a weed knife or crack weeder, or scald them with boiling water, then fix the joints. Sweeping or using a leaf blower on the patio regularly so debris never collects does more than any spray.

PreventionFull joints and regular sweeping - see weed control.

Joint repair and weeding tools

Amazon picks

As an Amazon Associate, PlantMapper may earn from qualifying purchases. Prices and availability are set by Amazon. Clean the joints out and let them dry completely before refilling. Check the joint depth, weather and temperature limits of any polymeric sand before you buy.

Group three

Water, moss, frost and salt

Standing water and puddles

Fix soon

What you notice. Puddles that hang around long after the rain stops, in the same spots every time.

Likely causesNot enough slope across the patio (it should fall about 1/8 to 1/4 in per foot away from the house), a slope that leads to a dead end against a wall or lawn edge, a few pavers that have settled, or a clogged drain.

How seriousWater that drains within an hour or two is a nuisance. Water still sitting there the next day is a real fault, and it brings algae, mosquitoes, frost damage and failing joints.

RemedyDump a couple of buckets of water and watch where it goes. A single puddle on an otherwise draining surface means settled pavers to lift and relay. If the water does not move at all, the patio needs regrading or a channel drain to catch it.

Full detailPatio Drainage.

Drain backing up

Usually simple

What you notice. A channel or trench drain overflowing, a catch basin full of water, or puddles around a grate that used to drain fine.

Likely causesLeaves, pine needles, mulch and silt in the vast majority of cases. After that: a clogged outlet pipe, a catch basin that was never emptied, a pop-up emitter stuck shut, or a dry well that is full, silted up or too small.

How seriousUsually an easy fix, and worth checking before you assume anything worse.

RemedyPull up every grate and look. Scoop out the channel and catch basin, then flush the pipe with a hose or clear it with a drain snake. If it is all clear and still backing up, the problem is farther down the line and a drainage contractor is the next step.

PreventionClear the grates after leaf drop each fall.

Moss

Cosmetic

What you notice. Green cushions in the joints and along the shady edge, thickest through the cool, wet months.

Likely causesDamp, shade and little air movement. Moss does not harm sound pavers; it just grows where surfaces stay wet. North sides of houses, spots under trees and the low corner of the patio go first, and it thrives in the Pacific Northwest and the humid Southeast.

How seriousCosmetic, though thick moss on a step or slope is slippery.

RemedyScrape or brush it out, then use a patio moss and algae cleaner if it keeps coming back, following the label. More light and air, better slope and trimming back overhanging shrubs are what stop it returning.

RoutineMoss removal.

Green and black algae

Slip risk

What you notice. A thin green, gray or black film over the surface that turns dangerously slick when wet.

Likely causesA surface that stays wet, shade, and organic debris to feed on. Porous concrete, flagstone and textured pavers hold it more than dense, smooth ones. Long humid summers along the Gulf Coast and Southeast keep it growing most of the year.

How seriousMinor cosmetically, but a leading cause of slips on patios. Treat it as a safety issue on steps and slopes.

RemedyScrub with water and a stiff brush, or use a patio algae and mildew cleaner made for pavers and concrete, following the label and keeping runoff out of storm drains. Then cut the moisture: fix the slope, clear drains, trim back plants and keep leaves swept off.

RoutineAlgae treatment.

Frost heave, scaling and de-icer damage

Permanent

What you notice. Pavers or slab corners pushed up after a cold snap, flaking or pitted concrete (scaling), crumbling stone edges, or pavers that split over winter.

Likely causesWater in the base or soil freezing and expanding. Frost heave is a problem wherever the ground freezes, from the Midwest and Northeast to the Plains and Mountain West, and worst on clay or silty soil with a thin or poorly drained base. Scaling on concrete comes from freeze-thaw plus de-icing salt, especially in the first winter or on concrete that was overworked when finished.

How seriousScaling and frost-split stone cannot be undone. Heaved pavers often settle back partly in spring but rarely to level.

RemedyLift and relay heaved pavers after the thaw, adding base and improving drainage (cold regions often use 6 to 8 in of gravel or more). Resurface lightly scaled concrete with a concrete resurfacer; replace badly damaged units. Skip rock salt and chemical de-icers on concrete in its first year, and avoid ammonium-based de-icers on concrete at any age; use sand for traction, and check the paver maker's advice on de-icers.

PreventionA thick, free-draining base, good slope and freeze-thaw rated pavers.

Mud pumping up through joints

Warning sign

What you notice. Muddy water oozing out of joints after heavy rain, or a fine silty film left on the surface around certain joints.

Likely causesWater moving under the patio and carrying soil with it. Usually soft clay with no geotextile fabric between soil and gravel, a base made with the wrong material, or a leaking pipe underneath.

How seriousSignificant. Soil washing out from underneath is what causes sunken areas later.

RemedyInvestigate rather than re-sand. Lift a few pavers and look at what is going on below, and check irrigation lines and downspout pipes if it happens in dry weather.

PreventionGeotextile fabric over soft soil - see preparing the ground.

Group four

Stains and appearance

Seldom serious, often maddening. How fast you act matters more than which product you buy.

Efflorescence

Normal

What you notice. A white, powdery haze on fairly new concrete pavers or a new slab, patchy, and often worse after wet spells in the first year.

Likely causesNatural salts in the concrete, mortar or base dissolving in water, moving to the surface and staying behind when the water evaporates. Very common on new concrete pavers, poured concrete and mortared stone.

How seriousNot a defect. It is part of new concrete drying out, and paver makers expect it.

RemedyOften nothing - rain, sun and foot traffic wear it away over months. Dry-brush it off. If it lingers, use an efflorescence cleaner made for pavers, exactly as directed, and rinse well. Skip straight muriatic acid, which can etch the surface and change its color.

NoteSealing pavers while they are still blooming locks the haze under the sealer.

Rust stains

Cosmetic

What you notice. Orange or reddish-brown spots and streaks, under metal furniture feet, a grill, around a sprinkler head, or speckled across the surface.

Likely causesSeveral. Metal furniture, grills and tools left out in the rain; lawn fertilizer granules containing iron landing on the patio; sprinklers spraying well water high in iron; or iron minerals inside some sandstone and flagstone oxidizing from within.

How seriousCosmetic. Natural iron spotting is a feature of the stone, not a fault.

RemedyA rust remover made for concrete and pavers, tested on a hidden spot first and rinsed well. Sweep fertilizer granules off the patio right after spreading. Iron from within the stone usually cannot be removed. Put pads under metal furniture feet.

CarefulMost rust removers are acidic and must never be used on limestone or marble.

Leaf and tannin stains

Cosmetic

What you notice. Brown leaf-shaped prints, dark patches under a tree, or general discoloration after fall.

Likely causesTannins leaching out of wet leaves, acorns, berries, pine needles and mulch left on porous surfaces. Oaks, maples and walnuts are common offenders, and aphid honeydew and bird droppings add to it.

How seriousCosmetic, but the longer it sits the deeper it soaks into porous concrete and stone.

RemedyScrub with water and a stiff brush first, then an oxygen-bleach patio cleaner if needed. Many tannin stains also fade in sunlight. The lasting fix is blowing leaves off in fall instead of leaving them all winter.

RoutineFall maintenance.

Grease, oil and wine stains

Cosmetic

What you notice. Dark spots under the grill or smoker, greasy patches around the dining table, or a red ring where a glass tipped over.

Likely causesPorous surfaces soaking up something oily or strongly colored. Unsealed concrete, pavers, sandstone and limestone are the vulnerable ones; porcelain barely stains.

How seriousCosmetic, but speed makes all the difference.

RemedyBlot, do not wipe, straight away. Cover with cat litter or another absorbent powder to pull out what you can, then use a paver degreaser or a poultice made for the surface. Old, set-in grease on porous concrete or stone may never fully come out.

PreventionA grill mat and a penetrating sealer under the cooking and dining area - see sealing.

Mortar and grout smears

Awkward

What you notice. A dull gray haze or hard smears on the surface, there from the day the job was finished.

Likely causesMortar, grout or cutting slurry left to dry on the face of the stone or pavers during installation.

How seriousCosmetic, but stubborn once cured, which is why good installers sponge it off as they go.

RemedyCement and mortar removers are sold for this, but most are acid-based, must never touch limestone or marble, and can etch or lighten other stone. Test in a hidden spot, follow the label exactly, and wet the surrounding surface first so the product cannot soak in where you do not want it.

PreventionWipe off residue while it is still wet.

Chipped and broken edges

Cosmetic

What you notice. Chipped corners, spalled edges along the joints, or a ragged outer edge where the patio meets the lawn or a gravel strip.

Likely causesImpact from dropped tools, dragged furniture, snow shovels and mower wheels. Also pavers set too tight with no joint, and outer pavers with no edge restraint behind them.

How seriousCosmetic on most materials. On porcelain a chip shows the body color and is hard to hide.

RemedySwap out badly damaged pavers. On natural stone, small chips weather in surprisingly well and are often best left alone. Fit proper edge restraint along the outside edge so it does not happen again, and use a plastic shovel or one with a rubber edge in winter.

PreventionProper joints and edge restraint - see finishing the edges.

Stain removal and cleaning

Amazon picks

As an Amazon Associate, PlantMapper may earn from qualifying purchases. Prices and availability are set by Amazon. Test any cleaner on a hidden spot first. Acid-based products must never be used on limestone or marble and can etch other stone and concrete. Follow the label, protect nearby plants and keep runoff out of storm drains.

Keeping it from coming back

The habits that prevent most of this

Nearly every fault above is prevented, or at least delayed, by the same few routines.

Every few weeksFive minutes

  • Sweep or blow it off so seeds and debris never settle in the joints
  • Move planters and furniture now and then so nothing stays wet underneath
  • Blot spills right away, especially near the grill

Each fallAn hour

  • Clear leaves promptly instead of letting them lie and stain
  • Lift every drain grate and empty the channel and catch basin
  • Check downspouts empty away from the patio, not onto it

Each springA morning

  • Wash it down with water and a stiff brush before the season starts
  • Walk the whole surface after the thaw and mark anything heaved, sunk or rocking
  • Treat algae if it took hold over winter

Every few yearsA day

  • Top up joint sand or replace tired polymeric sand
  • Repoint mortar joints that have started to crumble
  • Reseal if the patio was sealed and water no longer beads up

The full care routine, material by material

Cleaning, pressure washer settings, re-sanding, sealing and winter care with de-icers all differ between pavers, flagstone and concrete. The maintenance guide takes each in turn.

Patio Maintenance
Problem questions

Patio problems: frequently asked questions

Why are my pavers sinking or moving?

Because something underneath has moved. On a paver patio the usual culprits are a gravel base that was too thin or never compacted in layers, bedding sand laid too deep, no edge restraint so the field creeps outward, or water washing sand out through open joints. On a mortar-set flagstone patio it is usually voids under the stones. The lasting fix is to pull up the affected pavers, find and correct the soft spot in the base, rescreed about 1 in of bedding sand, relay, re-sand the joints and add or repair the edge restraint.

Can I just add more joint sand to a patio with loose pavers?

Only if the pavers are level and the base is sound. Joint sand locks pavers together sideways, but it cannot hold up a paver that has nothing solid under it. If pavers rock or have dropped, sand poured on top will wash out again by the next season. Lift and relay the low or rocking units first, then sweep in fresh sand or polymeric sand across the whole area.

Why did my polymeric sand fail or leave a haze?

Polymeric sand is fussy. It fails when joints are too shallow (most brands want the sand at least 1 to 1.5 in deep and the joint filled to about 1/8 in below the top of the paver), when it is installed on damp pavers or before rain, when it is not compacted into the joints, or when it is over-watered or under-watered while activating. A gray or white haze is polymer left on the paver faces because the surface was not blown completely clean before wetting. Thin haze often wears off; stubborn haze needs a polymeric haze remover. Failed sand has to be raked out and replaced following the bag instructions exactly.

How do I stop weeds growing between pavers?

Most patio weeds sprout from seed and dust that lodge in the top of the joints, not from roots pushing up through the base. Keep joints full and firm, sweep or blow the patio regularly so debris never builds up, and pull young weeds before they root deeply. Polymeric sand helps because it stays put, and a weed knife or boiling water clears what is already there. Herbicides only treat the symptom.

Why does water pool on my patio?

Either the patio was built too flat, the slope leads to a spot with no outlet, a few pavers have settled into a dip, or a drain is clogged. A patio should fall about 1/8 to 1/4 in per foot away from the house. Pour a couple of buckets of water and watch: one puddle in an otherwise draining surface means a few settled pavers you can relay; water that goes nowhere means the whole surface lacks slope and needs regrading or a channel drain. See Patio Drainage.

Is a crack in my concrete patio a problem?

Hairline shrinkage cracks are normal in concrete, especially if the slab had too few control joints, and they are cosmetic. Worry when a crack is wider than about 1/4 in, when one side sits higher than the other, when it keeps widening, or when it runs toward the house foundation. Those suggest settlement, frost heave or tree roots, and are worth having a concrete contractor look at.

What is the white powder on my new pavers?

Efflorescence. Water moving through new concrete pavers or concrete carries natural salts to the surface and leaves them behind as it evaporates. It is very common in the first year, it does not mean the pavers are faulty, and it usually fades on its own with weather and foot traffic. Brush it off dry. If it lasts, use an efflorescence cleaner made for pavers, and do not seal the patio until it has stopped appearing.

How do I get rid of moss and algae on a patio?

Scrape and brush out the bulk, then use a patio cleaner rated for moss and algae, following the label and keeping it off nearby plants and out of storm drains. In humid parts of the country such as the Southeast, Gulf Coast and Pacific Northwest it will come back unless you deal with the cause: shade, poor slope, debris and joints that stay wet. More light, better drainage and regular sweeping keep it away.

Why is my patio so slippery?

Usually a thin film of algae or mildew rather than the material itself. It builds up wherever pavers or concrete stay damp, especially in shade and through mild, wet winters, and it can make a perfectly good surface dangerous. Clean it off and cut the moisture. If a surface is slippery even when clean and dry, the finish may be wrong for outdoor use; see slip resistance.

What is frost heave and how do I fix it?

Frost heave happens when water in fine, poorly drained soil under a patio freezes and forms ice lenses that push the surface up, often unevenly. It is common across the northern half of the country, from the Midwest and Northeast to the Mountain West. Pavers usually settle back partly in spring; concrete may crack. The fix is a thicker, well-drained gravel base (often 6 to 8 in or more in cold regions), good slope and keeping water out of the base. Lift and relay heaved pavers after the ground thaws.

Why is my concrete patio flaking?

That is called scaling. It happens when a concrete surface takes up water and goes through repeated freeze-thaw cycles, and it is made much worse by de-icing salts, especially on concrete less than a year old or concrete that was overworked or finished with water on the surface. Scaling cannot be reversed. Light scaling can be resurfaced with a concrete resurfacer; badly scaled slabs need replacing. Avoid rock salt and chemical de-icers on concrete in its first winter, and use sand for traction instead.

How do I get rust stains off pavers or concrete?

Rust from metal furniture, grills, fertilizer granules or irrigation water with iron in it can usually be lifted with a rust remover made for concrete and pavers. Test it in a hidden spot first, rinse well and never use acidic products on limestone or marble. Orange spotting that comes from inside some natural sandstone and flagstone is iron in the stone itself and generally cannot be removed.

Should I power wash my patio?

Carefully. A pressure washer with a narrow tip, held close, blasts sand out of paver joints, etches concrete and can scar soft stone, leaving a rough surface that gets dirty faster. Use a 25 or 40 degree tip or a surface cleaner attachment, keep the wand back, work at a shallow angle and do not aim along the joints. Plan to re-sand the joints afterward. For many patios a stiff brush and a patio cleaner does the job with less risk. See pressure washing.

My patio is sending water into the basement. What should I do?

Act soon. The likely cause is a patio that slopes toward the house, has settled near the foundation, or sits too high against the siding so water runs behind it. Ground and paving next to a house should fall away from it, and the patio surface should stay below the door threshold and below the bottom of the siding by the clearance the siding maker specifies. Because this damages the house rather than the yard, have a contractor or foundation specialist look at it on site.

Should I repair my old patio or replace it?

Repair makes sense when the problems are local, such as a few sunken pavers, one cracked flagstone, tired joint sand or a clogged drain, and the overall slope is right. Replacement starts to make sense when the whole patio holds water, when settlement or heave is widespread, when several faults show up together, or when matching pavers are no longer made. If the same fault keeps returning within a year or two of fixing it, the base is the problem, not the surface.

How long should a patio last?

A well-built paver or flagstone patio on a properly compacted gravel base can last 25 years or more with routine care, and pavers can be lifted and relaid rather than thrown away. A concrete patio typically lasts 20 to 30 years or more, depending on climate, base and how it was finished. What shortens a patio's life is rarely the surface: it is a thin base, poor compaction and water with nowhere to go.

The small print

Notes and limitations

Diagnosing from a distance has limits

This page covers the usual causes of each fault. Your patio may have a different or extra cause, and often the only sure way to find out is to lift a paver and look.

Houses and structures

Water getting into a house, a retaining wall that is moving and cracks that keep growing near a foundation should be checked in person by a contractor, engineer or foundation specialist, not diagnosed from a web page. Before digging, call 811 to have buried utilities marked.

Chemical cleaners

Patio cleaners, rust removers, efflorescence cleaners and mortar removers vary a lot, and many are acidic. Test on a hidden spot, never use acid products on limestone or marble, follow the label, and protect nearby plants, lawns and storm drains.

Trees and roots

Cutting large roots that lift a patio can harm or destabilize the tree. Some cities and HOAs protect certain trees, so check local rules, and ask a certified arborist before cutting significant roots.

De-icers

Rock salt and many chemical de-icers speed up scaling on concrete, can damage some pavers and stone, and harm nearby lawns and plants. Avoid them on new concrete, check what the paver or stone maker recommends, and use sand for traction where you can.

Affiliate links

Some links on this page are Amazon affiliate links. PlantMapper may earn a commission from qualifying purchases at no extra cost to you. It never affects which products we suggest. See our affiliate disclosure.