How to Build a Raised Planter: Base, Frame, Liner and Fill
The build itself is simple. What separates a planter that is still square and solid in fifteen years from one that has bowed, sagged and rotted is all in the parts nobody photographs: a level base, corner posts that carry the load, a liner that keeps wet soil off the wood, and drainage that actually works.
General advice for American yards. Anything holding back more than about 2 ft of soil, or built against a house wall or a property-line fence, needs more care than a weekend project; above about 3 to 4 ft it is a retaining wall, which many jurisdictions regulate, so check locally. Keep soil at least 6 in below any wood siding, and call 811 before digging. Part of the PlantMapper Raised Planters section.
The corners and the base decide whether it is still square in fifteen years · photograph via Pexels
Before you start
What you are really building against
Soil is far heavier than people expect. Wet soil weighs roughly 90 to 100 lb per cubic foot, so an 8 x 4 ft planter filled 2 ft deep holds about 64 cubic feet, or around three tons once it is watered.
That weight pushes out on the sides, down on the base and into any soft spot underneath. Every rule that follows comes from that one fact: brace the sides, set the base on something firm, and never assume hardware that holds a fence will hold a planter.
This guide assumes a wooden planter, since that is what most people build. Masonry planters follow the same principles for base, liner and fill, but the walls themselves are usually a mason’s job. See block, brick and stone.
What you need
Tools and materials for a wooden planter
A weekend project for two people. Nothing here is specialized except the drill.
✓Tools
Cordless drill/driver with pilot and countersink bits.
Circular saw or handsaw; a miter saw makes square cuts much easier.
A 4 ft level, not a torpedo level.
Tape measure, pencil, speed square, mason’s string and stakes.
Shovel, rake and a hand tamper (a scrap 4x4 works for a small planter).
Wheelbarrow, gloves and a utility knife or scissors for the fabric.
!Materials
2x boards (1½ in thick), rated for ground contact, or cedar or redwood, cut to length.
4x4 corner and middle posts, the same rating or species.
Exterior screws rated for treated lumber, stainless or coated, 3 to 3½ in long.
End-cut preservative (copper naphthenate) for every cut on treated lumber.
Permeable landscape fabric or a heavy pond liner, and a staple gun with stainless or galvanized staples.
Paver base or crushed gravel for the base; clean ¾ in gravel for a drainage layer.
Topsoil-and-compost blend to fill it. Work out the cubic feet first.
The part that decides everything
Preparing a firm base
A planter is only as square as the ground it stands on. Ten extra minutes on the base saves you a leaning planter in three years, and the method depends on what is underneath. Call 811 a few days before you dig, and check for sprinkler lines.
On soil, lawn or a flower bed
The most common situation and the easiest, because the ground underneath will carry the load and roots can grow down into it.
Mark it out
Lay out the footprint with string and stakes, and check that the diagonals match. That is what makes it square.
Remove the sod
Cut out sod and weeds from the whole footprint plus about 4 in all around. Perennial weeds such as bindweed, quackgrass and Bermudagrass will come up through a planter, so get the roots out now.
Level a firm strip
You do not need to level the whole area. Level a firm strip about 12 in wide under each wall, cutting off high spots rather than filling low ones. Cut ground is stable; filled ground settles.
Firm it
Tamp the strips until they no longer give under your heel.
Loosen the middle
Loosen the soil inside the footprint to a shovel’s depth. It lets water drain away, lets roots down and stops the planter sitting on a compacted hardpan.
Do not lay plastic sheeting under a planter on soil. Permeable landscape fabric to block weeds is fine, and hardware cloth stops gophers and voles where they are a problem, but anything waterproof turns the planter into a bucket.
On a patio, concrete or a courtyard
Simple, as long as water can get out and the bottom is not sitting in it.
Check the surface is sound and roughly level
Patios are usually built with a slight slope for drainage, which is fine. Shim any rocking under the planter walls with composite or plastic shims rather than mortar.
Lift the planter off the surface
Set it on treated 2x4 runners, plastic feet or a bed of gravel so the bottom boards are not permanently wet. That alone adds years to a wooden planter.
Make sure water can escape
Water leaving the planter has to go somewhere. Check where it will run, and keep it away from the house foundation.
Build a bottom if the planter is closed
A planter on concrete needs a slatted or drilled bottom with a generous drainage layer above it. See
drainage.
Remember the weight. Filled and watered, even a modest planter weighs well over a ton, so think carefully before setting one on a deck, a balcony or a rooftop, and have a pro check that the structure will carry it.
On sloping ground
A planter on a slope must be level, which means one end is dug in and the other stands up higher.
Cut, don’t fill
Dig into the slope at the high end rather than building up the low end. Cut ground is undisturbed and stable; fill settles and takes the planter with it.
Set the level from the high end
Set the finished top height from the high side and work down, so the buried depth is at the uphill back where it does least harm.
Make the downhill side stronger
The downhill wall holds more soil and more outward pressure, so give it extra posts, about every 2½ ft instead of every 3 ft.
Deal with water coming from above
A planter across a slope dams water running downhill. Dig a shallow gravel trench above it, or the ground behind will stay soaked. See French Drains and Dry Wells.
Above about 2 ft of held-back soil you are building a retaining wall rather than a planter, and it needs proper design. Get advice, and check local rules for taller walls.
Getting it truly level
Level matters more on a planter than almost anything else in the yard, because the top edge is near eye level and any error shows.
Use a 4 ft level, not a short one. Short levels mislead over long distances.
Check level along each wall, across the middle and corner to corner.
Check the diagonals of the footprint match before fixing anything. Equal diagonals
mean square corners.
Where a planter is close to a wall or fence, set it parallel to that line even if
the line itself is slightly off - the eye compares it with the wall, not with
true.
Where several planters sit together, level them to one another. Two planters at the same height always look better than two that are each perfect on their own.
Putting it together
Construction, step by step
The standard method: four corner posts, boards screwed to the posts from outside, middle posts where a side is long. It is quick, strong and easy to repair.
Cut everything and treat the ends
Cut all the boards and posts to length before assembling anything, and check that matching pieces are identical. A difference of an ⅛ in shows badly at a corner.
On treated lumber, every cut exposes wood the treatment did not fully reach, and that is where rot begins. Brush end-cut preservative onto every cut, including screw holes in end grain, and let it soak in. Cedar and redwood need no end treatment.
Set the corner posts
Posts go inside the planter, at the corners, with the boards screwed to them from outside. On soil you can sink them 8 to 12 in into the ground for extra stiffness; on a patio they simply stand on it.
Posts should run the full height of the planter and stop about ½ in below the top board so the cap rail can cover them.
Fix the bottom board first
Screw the lowest board to two corner posts, check it is level along its length, and only then attach the next side to it. Getting the first board level is what makes every board above it level.
Use two screws into each post at every board. One screw is a hinge.
Work round and up
Attach the four bottom boards to make a square frame, check the diagonals match, adjust if they do not, then build up in courses. Butt the boards tight; small gaps let soil wash out and are hard to close later.
Stagger the vertical joints between courses if you are using short lengths, exactly as you would with brickwork.
Add middle posts on long or wide sides
Any side longer than about 4 ft needs a middle post; anything over 8 ft needs two. Without them the boards bow outward under wet soil and the corners start to open.
On a planter wider than about 4 ft, add a cross-brace across the top between opposite sides, a length of 2x4 or a threaded rod. It is the cheapest insurance in the whole build.
Cap the top
A cap rail is optional structurally and transforms the planter in use. It covers the end grain and the post tops, keeps rain out of the boards, gives you somewhere to sit and set things down, and finishes the planter properly.
Miter the corners if you can; a butt joint works but shows. Fasten from above with countersunk screws and treat the cuts.
Check it before any soil goes in
Push firmly on the middle of each long side. There should be almost no movement. Check the top is level all round and the diagonals still match.
This is the last moment when anything is easy to correct. Once it is full, it is full.
The details that fail first
Screws and joints
More planters fail at the fasteners than anywhere else, and almost always for one of the same four reasons.
Fasteners for raised planters, and where each one belongs.
Fastener
Use it for
Notes
Exterior screws rated for treated lumber, 3 to 3½ in
Boards to posts, general assembly
Two per board per post. Pre-drill near board ends to avoid splitting
Stainless steel screws
Cedar, redwood and coastal yards
Tannins in cedar and redwood react with plain steel and leave black streaks; stainless avoids it and never rusts in salt air
Timber screws or lag screws, 6 to 10 in
Fastening landscape timber courses together
Pre-drill, and stagger the screws between courses
Threaded rod and washers
Through-bolting thick timbers or a cross-brace
The strongest option; drill right through and tighten evenly
Galvanized corner brackets
Reinforcing inside corners
A cheap way to stiffen a planter built from thin boards
Nails
Nothing structural
Nails work loose as wood swells and shrinks. Do not build a planter with them
Post anchors or concrete
Setting posts in very soft ground
Rarely needed; a planter full of soil is heavy enough to stay put
✓Do
Use two screws per board per post. A single screw lets the board pivot.
Pre-drill within 2 in of the end of any board.
Countersink so screw heads sit flush; raised heads snag clothes and hands.
Use stainless or coated screws rated for treated lumber, which corrodes plain steel.
Treat every cut end and drilled hole on treated lumber with end-cut preservative.
Add a cross-brace across the top of anything wider than about 4 ft.
!Do not
Do not use nails, drywall screws or plain zinc-plated screws that will rust.
Do not rely on the corner posts alone on a side longer than 4 ft.
Do not screw a planter to a fence or the house. It must stand on its own, with a gap behind.
Do not leave screw heads sticking up, or screw tips poking through on the inside.
Do not skip pre-drilling near the ends of boards; you will split them.
Do not use boards thinner than 1½ in and expect them to stay straight.
Getting this right
Lining a planter properly
Lining is the most misunderstood step in the whole build. It protects the structure, not the plants, and lining the bottom is a mistake that ruins planters.
Line the walls, never seal the bottom
The liner goes up the inside of the walls and stops short of the bottom, or is cut generously so water can leave freely at the base. A planter with a sealed bottom becomes a sump; the soil turns sour and roots drown.
If you want weed control at the bottom, use permeable landscape fabric, which lets water through. Never lay a solid plastic sheet across the bottom.
Choose the right material
Permeable landscape fabric is the all-purpose answer: cheap, breathable, easy to staple, and it keeps soil off the wood while letting water through. It is the right choice for most wooden planters.
A heavy pond liner or thick plastic on the walls only is worth it for a planter you want to last, or against masonry and metal, where it also stops staining and efflorescence. Leave the bottom open or punch holes in it.
Staple it high and neatly
Run the liner up to just below the top of the boards and staple it closely along the top edge. Trim it about ½ in below the cap rail so it is invisible when the planter is full.
Overlap seams by about 6 in and work from the corners outward so the liner does not bunch and pull down as you fill.
Line masonry and metal for their own sake
Brick, stucco and block suffer badly from permanently wet soil behind them: staining, efflorescence and eventually failing stucco. A lined wall stays sound.
Metal planters in full sun benefit from an insulating liner, bubble insulation or rigid foam board, which evens out temperature swings at the roots.
Know when not to line
A planter on open soil, where you want roots to reach the ground below, needs no bottom liner at all. Loosen the ground instead.
Cedar and redwood heartwood do not strictly need lining, though it still adds years. Do not line a dry-laid stone planter: the free drainage is the point.
The most common lining mistake is a plastic sheet across the bottom of the planter, often added with the best intentions, to keep weeds out. It traps every drop of water that goes in. If you inherit a planter that will not stop being waterlogged, this is the first thing to check.
As an Amazon Associate, PlantMapper may earn from qualifying purchases. Prices and availability are set by Amazon. Line the walls but never seal the bottom. A solid sheet across the bottom is the most common cause of a waterlogged planter.
Water has to leave
Drainage and avoiding waterlogging
A raised planter should drain better than the ground around it. When one does not, it is nearly always for one of four reasons, all avoidable while you build.
On open soil
The simplest case
Water leaves through the bottom into the ground below, so all you need is for that ground to take it. Loosen the base before filling and do not lay anything waterproof.
Loosen the footprint to a shovel’s depth before building.
Use permeable landscape fabric only, if anything at all.
On heavy clay, add 2 to 4 in of coarse gravel at the bottom.
If the ground around it stays soggy, fix that first. See Yard Drainage.
On a patio or concrete
Where drainage must be built in
Water cannot drain down, so it has to go out through the sides, and the bottom must not sit in a puddle. This is where most waterlogged planters come from.
Leave ¼ to ⅜ in gaps between the lowest boards, or drill ¾ in holes about every 12 in.
Add 3 to 4 in of clean ¾ in gravel at the bottom, separated from the soil above by landscape fabric.
Set the whole planter on feet or 2x4 runners so the bottom boards are clear of the surface.
Check where the water will run, and keep it away from the house foundation.
Closed-bottom planters
Planter boxes and elevated planters on legs
A planter with a solid bottom needs holes, and more of them than people expect. One hole in the middle is not enough for a big planter.
Drill ¾ in holes about every 12 in across the whole bottom.
Use slats with ⅜ in gaps instead of solid plywood where you can.
Cover the bottom with landscape fabric so soil does not wash straight out.
Never set a closed planter flat on a patio with no clearance underneath.
Diagnosing a wet planter
Four causes, in order of likelihood
If a planter stays soggy, work through these before adding anything. It is almost never the soil mix alone.
A sealed bottom: plastic sheeting, a solid liner, or a plastic tray underneath. By far the most common cause.
Nowhere for water to go: too few holes, or holes clogged with soil because no fabric was used.
The planter is sitting in standing water on the surface below it.
The fill is too fine: straight potting mix or heavy topsoil with nothing coarse in it. See filling it.
What goes in it
Filling a raised planter
The fill matters more than what the walls are made of. Straight bagged potting mix is the classic mistake: it looks perfect on day one, settles by half within a year and holds very little nutrition.
What to fill a raised planter with, from the bottom up.
Layer
Depth
What to use
Why
Drainage layer (patios and slabs only)
3 to 4 in
Clean ¾ in gravel or crushed stone, with landscape fabric above it
Gives water somewhere to go where it cannot soak away
Filler layer (deep planters only)
Up to a third of the height
Logs and branches (the hugelkultur approach), sod laid upside down, or clean broken concrete
Fills volume cheaply and breaks down into organic matter. Do not use it where roots need the depth
Main fill
The rest, at least 12 to 16 in
60% screened topsoil or a topsoil-and-compost blend, 30% compost or aged manure, 10% coarse sand or fine pine bark
Holds water and nutrients like real soil, does not slump, drains freely
Top dressing
1 to 2 in
Compost, or a mulch of shredded bark or gravel for ornamentals
Feeds, conserves moisture and suppresses weeds
✓Good fill
A topsoil-and-compost blend, sold by the cubic yard as "raised bed mix" or "garden blend".
Roughly 60% topsoil, 30% organic matter, 10% coarse sand or fine bark, mixed, not layered.
Screened topsoil, so there are no rocks, weed roots or clods of clay.
Extra coarse sand or fine gravel for herbs, succulents and anything Mediterranean.
An acidic mix made for acid-loving plants, in its own planter, for blueberries, azaleas and camellias.
Bought in bulk above about a cubic yard, usually far cheaper than bags.
!Poor fill
Straight bagged potting mix: settles by up to half in the first year and runs out of nutrients by midsummer.
Raw subsoil or clay dug from a foundation, which sets hard and drains badly.
Fresh manure or fresh grass clippings, which heat up and burn roots.
Soil from a bed with clubroot, root-knot nematodes, persistent perennial weeds or a Bermudagrass problem.
Fine play sand, which clogs the pores instead of opening them. Use coarse builder’s sand or fine bark instead.
A gravel layer inside an ordinary planter on open soil: it does nothing useful and wastes depth.
Fill in layers and water as you go
Add 8 to 12 in at a time, rake it roughly level and water it in. Fill a planter dry and then water it, and the whole thing sinks 4 in in the first rain.
Do not stomp it down. The whole point of a planter is that the soil is never compacted, and watering settles it perfectly well.
Leave a watering gap
Finish the soil about 2 in below the top of the planter. Filled to the brim, water and compost wash over the edge every time you water.
That gap also leaves room for a yearly layer of compost without raising the level.
Expect it to settle, and top it up
Any fresh fill drops over the first few weeks. Wait two weeks, then top up to the level you want before planting.
Every spring after that, add 2 in of compost on top. That is the entire soil care routine for a planter. No digging required.
Organic matter is a third of the mix, never the whole of itGood fill holds water and feeds like real soil, because it largely is real soilA gravel layer belongs at the bottom of a planter on a patio, not one on open soil
Avoid these
Six construction mistakes
These are the ones that show up in year two or three, when they are difficult to fix.
1. Sealing the bottom
A plastic sheet or sealed liner across the bottom turns the planter into a bucket. The soil turns sour, roots drown and nothing thrives, and you cannot see it once the planter is full.
The fixLine the walls, not the bottom. Use permeable landscape fabric if you want weed control underneath, and make sure water has a clear way out.
2. No middle posts on a long side
Boards longer than about 4 ft bow outward under the weight of wet soil, and once they bow the corner joints open and soil starts to wash out.
The fixAdd a middle post every 3 to 4 ft, and a cross-brace across the top of anything wider than about 4 ft.
3. Building on soft or uneven ground
A planter built on loose fill settles unevenly within a year or two and leans. Because it is near eye level, even a small lean is very obvious.
The fixLevel a firm strip under each wall by cutting rather than filling, tamp it well, and check the diagonals before fastening anything.
4. Filling it with straight potting mix
Bagged potting mix looks ideal and is the wrong material: it settles by up to half in the first year, holds little nutrition past midsummer and dries to a crust that sheds water.
The fixUse roughly 60% topsoil, 30% compost or aged manure and 10% coarse sand or fine bark, mixed together. Buy it as a bulk raised-bed blend from a landscape supply yard if you would rather not mix it yourself.
5. Leaving cut ends untreated
Every cut on treated lumber exposes wood the treatment did not fully reach, right where water sits. It is the most common reason a treated planter rots years early.
The fixBrush end-cut preservative on every cut and drilled hole as you go, before assembly, and keep the can handy for any changes.
6. Filling to the brim
A planter filled level with the top edge loses water, compost and mulch over the side every time you water or it rains hard.
The fixStop the soil about 2 in below the top. It looks better, holds water where it is needed and leaves room for the yearly compost.
Print it or check it off as you go
The build checklist
Fifteen steps from bare ground to filled planter. Your checks are saved in this browser only.
Base
Build
Liner and fill
Questions
Building a raised planter: your questions answered
Answers to the questions homeowners ask most.
Do I need to line a raised planter?
Line the walls, yes; never seal the bottom. Permeable landscape fabric or a heavy pond liner on the inside walls keeps permanently wet soil off the wood and adds several years to its life, and on brick, stucco or metal it also prevents staining and efflorescence. What you must not do is lay a waterproof sheet across the bottom. That turns the planter into a bucket, and it is the most common cause of a planter that will not stop being waterlogged.
What should I put in the bottom of a raised planter?
On open soil, nothing: loosen the ground so roots and water can get through, and fill with soil (add hardware cloth first if gophers or voles are a problem). On a patio or concrete, put down 3 to 4 in of clean ¾ in gravel with landscape fabric above it, so water has somewhere to collect and leave. In a deep planter you can also part-fill the bottom with logs and branches, upside-down sod or clean broken concrete to save on soil, as long as you leave at least 12 to 16 in of real soil above it.
What soil should I fill a raised planter with?
Roughly 60% screened topsoil, 30% compost or aged manure and 10% coarse sand or fine pine bark, mixed together rather than layered. Landscape supply yards sell this as "raised bed mix" or "garden blend", and above about a cubic yard it is usually far cheaper delivered in bulk than in bags. Do not fill a planter with straight bagged potting mix: it settles by up to half in the first year, holds little nutrition past midsummer and dries to a crust that sheds water.
How do I stop the sides of a wooden planter bowing?
Three things, and you need all three. Use 2x boards at least 1½ in thick, because ¾ in boards bow within a season. Add a middle post every 3 to 4 ft on any side longer than 4 ft, not just at the corners. And fit a cross-brace across the top between opposite sides on anything wider than about 4 ft. Wet soil pushes outward surprisingly hard, and once boards bow the corner joints start to open.
Can a raised planter go right on a patio?
Yes, as long as water can escape and the bottom is not sitting in it. Leave ¼ to ⅜ in gaps between the lowest boards or drill ¾ in holes about every 12 in, add a gravel drainage layer with landscape fabric above it, and set the whole planter on feet or 2x4 runners so the bottom boards are clear of the surface. Check where the water will run and keep it away from the house foundation. Also allow for the weight: wet soil is roughly 90 to 100 lb per cubic foot, so never put a large planter on a deck or balcony without checking it can carry the load.
How deep should the drainage layer be?
On a patio or slab, 3 to 4 in of clean ¾ in gravel with landscape fabric between it and the soil. On open soil you do not need one at all: the ground below is the drainage layer, and gravel there just wastes root depth. The classic mistake is adding gravel to a planter on open ground because that is what people do in pots; in a big planter on soil it achieves nothing.
What screws should I use for a raised planter?
Exterior screws rated for treated lumber, stainless or coated, about 3 to 3½ in long, two per board per post. Modern copper-based treated lumber corrodes plain steel, and cedar and redwood tannins leave black streaks around it, so stainless is the safest choice near the coast and with cedar. Pre-drill within 2 in of the end of a board so it does not split, countersink so no head sticks up, and treat drilled holes in treated lumber with preservative. Do not use nails for anything structural: wood swells and shrinks and nails work loose.
How long does it take to build a raised planter?
A simple wooden planter about 6 x 3 ft is a comfortable day for two people, including the base, and only two or three hours of that is actual construction. Filling takes longer than building: moving a cubic yard of soil by wheelbarrow is a couple of hours of steady work. A masonry planter is a bigger project, needing a footing that has to cure before the wall goes up, and it is usually a job for a mason.