Landscape Lighting · Controls & Care

Timers, Sensors, Smart Controls and Keeping Your Lights Working

Controls are the difference between landscape lighting you enjoy every night and lighting you forget to turn on. They also cut the electric bill, keep the neighbors and wildlife happier, and stop the whole yard glowing at 3am. Most of them simply plug into your GFCI outdoor outlet.

General advice for American homeowners. Any new outdoor outlet or circuit, and any hardwired switch, timer or sensor on 120V, should be installed by a licensed electrician, usually with a permit under your local code. Unplug the transformer or switch off the power before cleaning or working on any fixture. Part of the PlantMapper Landscape Lighting section.

A backyard at night with softly lit lawn and trees
Lights that turn themselves on are lights that get enjoyed · photograph via Pexels
Why controls matter

Three things a good control does

It gets the lighting used. Lights that come on by themselves at dusk are enjoyed every evening; lights behind a switch in the garage get remembered about twice a summer.

It cuts the electric bill and the nuisance. A system that runs from dusk to 10 or 11pm uses a fraction of the power of one that runs all night, bothers neighbors and wildlife far less, and looks no different to anyone actually out in the yard.

It gives you more than one setting. A yard needs different lighting for dinner on the deck, for walking the dog, and for looking out at from the kitchen in January, and the way to get that is separate zones rather than more fixtures.

The options

Timers, photocells, sensors and switches

Several kinds of control, and most yards end up using two or three of them on different zones.

Landscape lighting controls compared.
ControlHow it worksBest forWatch for
Manual switchAn indoor wall switch, or a weatherproof outdoor oneAmbient lighting you want on when you want itGets forgotten; the most common reason lighting goes unused
Plug-in timerA weatherproof timer between the outlet and the transformer, or built into itString lights, 12V transformers, anything plugged inFixed clock times drift out of step with sunset, and daylight saving time throws them off
Astronomical timerA timer that works out sunset and sunrise for your location and dateThe best single control for landscape lightingNeeds setting up once with your ZIP code or location; worth it
PhotocellA light sensor that switches on at dusk; many transformers include oneEntry and porch lighting you want on every nightKeep it out of the beam of the light it controls, or it flickers on and off
Motion sensor (PIR)Detects movement and switches on for a set timeSecurity, side yards, the walk to the trash cans, gatesFalse triggers from cats, raccoons, deer, passing cars and branches
Dusk-to-dawn photocellOn at dusk, off at dawnPorch and safety lighting onlyWasteful and intrusive for landscape lighting; use an astronomical timer instead
Outdoor smart plugAn outlet controlled by an app, schedule or voice assistantString lights and 12V transformers; scenes and schedulesNeeds a reliable Wi-Fi signal where the outlet is
Smart transformer / hardwired systemApp or hub control, dimming and scenes across several zonesLarger or professionally installed systemsAny 120V hardwiring is electrician work; keep a manual override

✓A control plan that works for most yards

  • Front entry and porch lights on a photocell or astronomical timer, on every night from dusk.
  • Path and step lighting on an astronomical timer, dusk until a sensible hour.
  • Accent lighting on the same timer, or its own zone so it can go off earlier.
  • String lights and deck lighting on a smart plug or switch, because you want them on demand.
  • Security lighting on a motion sensor with a short on-time, completely separate from the landscape lights.
  • A manual override on everything, so you can turn it on for a party or off to watch a meteor shower.

!What to avoid

  • A single switch running the whole yard, which forces every light on at once.
  • Everything on dusk-to-dawn, which burns power all night for nobody’s benefit.
  • Fixed-clock timers set once in June and never touched, so by October they come on two hours after dark, and daylight saving time knocks them off by another hour.
  • A photocell mounted where its own light shines on it. It will switch on and off all night.
  • A security floodlight tied into the landscape lighting, so it trips while you are sitting outside.
  • A smart system with no manual way to turn the lights on when the Wi-Fi is down.

If you buy one control, make it an astronomical timer, or a smart plug or transformer that can schedule from sunset. It knows sunset for your location and date, so the lights come on at dusk all year, through daylight saving changes, with no adjusting, and off at whatever time you choose. It is the one change that turns landscape lighting from something you remember occasionally into something the yard just does.

Controls and timers

Amazon picks

As an Amazon Associate, PlantMapper may earn from qualifying purchases. Prices and availability are set by Amazon. Any control hardwired into 120V house wiring is work for a licensed electrician.

Splitting it into zones

Zones and runs

After getting the fixtures right, the most useful thing you can do for a lighting system is stop switching all of it together.

  1. Group by when you want it on, not by where it is

    The natural grouping is not "front yard and backyard" but "on every night", "on when we are outside" and "on only when something moves".

    Three zones along those lines cover nearly every backyard and make the whole system far more usable.

  2. Keep security lighting on its own

    A motion-triggered floodlight has nothing to do with the landscape lighting and should never share its control. Otherwise it fires while you are eating dinner outside.

    Give it its own sensor, its own short on-time, and its own switch so you can turn it off for an evening.

  3. Separate the accent lights from the path lights

    Path and step lighting is a safety layer and should be on whenever anyone is likely to be outside. Accent lighting is a view, and can go off at 10 or 11pm.

    Splitting them lets you run the accents for less time, which is where most of the energy savings and the neighbor goodwill come from.

  4. Put deck and patio lighting on demand

    String lights and seating-area lighting get used when you are out there, which is unpredictable. A smart plug, a remote or a weatherproof switch by the back door works far better than a timer.

    Dimming this zone, if you can, does more for how much the deck gets used than anything else.

  5. Plan the zones before the wire goes in

    Splitting zones later means new wire runs. Deciding on three or four zones at the planning stage costs nothing and is awkward to add afterward.

    On a 12V system that can simply mean a transformer with several outputs or zone controls, or two transformers, each with its own timer.

Getting sensors right

Motion sensors that work

A motion sensor that triggers constantly gets switched off within a month, which is why so many security lights are either permanently off or permanently on.

✓Setting a sensor up properly

  • Aim it across the approach, not straight down it. Passive infrared sensors pick up movement across the field far better than movement toward them.
  • Mount it at the height the manufacturer gives, commonly around 6 to 8 ft. Too high and it misses people; too low and it sees every cat.
  • Turn down the sensitivity and the range until it covers the area you care about and nothing more. Most sensors come set far too wide.
  • Use the masking shields or zone settings to block out the sidewalk, the street, the neighbor’s yard and any trees.
  • Set a short on-time. One or two minutes is plenty. Long settings waste power and annoy people.
  • Set the light-level (dusk) setting so it only triggers after dark, not on a gray afternoon.

!Why sensors misbehave

  • Aimed at a heat source: a dryer vent, an air conditioner condenser, a sunny wall or a furnace vent will trigger it again and again.
  • Moving plants: a branch or tall grass in the detection zone triggers it every time the wind blows.
  • Animals: cats, raccoons, opossums, skunks and deer are the most common reason a sensor fires all night. Raising the mount and narrowing the zone helps.
  • Cars and people on the sidewalk caught by a zone set too wide.
  • The light shining back on the sensor, which can hold it on.
  • Spiders and webs right across the lens, which is genuinely common and takes ten seconds to fix.

If a motion light has been firing all night, check the lens first: a spider sitting on it or a web across it will trigger it constantly, and it is by far the most common cause. Wipe the lens, then narrow the zone and lower the sensitivity before deciding the unit is faulty.

The modern option

Smart controls

Smart control of landscape lighting has become genuinely useful, mostly thanks to the humble outdoor smart plug and the app-controlled transformer rather than anything elaborate.

Smart plugs

The cheap, effective option

A weatherproof outdoor smart plug between the GFCI outlet and a transformer or string lights gives you schedules, sunset triggers, voice control and remote switching for very little money and no wiring.

  • It must be rated for outdoor use. An indoor smart plug inside a weatherproof box is not the same thing.
  • Look for sunset and sunrise scheduling rather than fixed clock times.
  • Check it keeps its schedule if the Wi-Fi drops; cheap ones often do not.
  • One per zone lets you build zones with no new wiring. Many transformers now have built-in app control too.

Smart bulbs and fixtures

More control, more to go wrong

Individually controlled outdoor fixtures give dimming, scenes and color, at the cost of complexity and dependence on a hub, an app and your network.

  • Dimming is the genuinely useful feature; color changing is a novelty in a yard, best saved for the holidays.
  • Wi-Fi signal at the back of a big lot is often the limit. Check it before buying.
  • Products get discontinued. Choose something you could still buy a replacement for in five years.
  • Keep a manual switch so the lights work when the network does not.

Scenes and scheduling

What to actually set up

The point of smart control is not the app. It is that the yard does the right thing without anyone thinking about it.

  • A sunset-triggered schedule for path and accent lighting, off at a set time.
  • An "evening outside" scene for the deck or patio, dimmed and warm.
  • A "just the path" setting for taking out the trash.
  • A vacation schedule for the porch lights, varied a little rather than identical every night.

What to be wary of

Keep it simple

Smart control is at its best doing simple things reliably. Complexity is what makes people stop using it.

  • Always keep a manual override, and make sure everyone in the house can turn the lights on without the app.
  • Avoid tying your landscape lighting to a system you would have to replace all at once.
  • Do not put security lighting behind an app. It should work no matter what.
  • Any hardwired 120V smart switch, controller or sensor is electrician work, like any other permanent wiring.
Keeping it working

Cleaning and maintenance

Landscape lighting fails from three things: dirty lenses, water getting in and fixtures getting knocked out of aim. All three are handled by twenty minutes twice a year.

Twice a year, twenty minutes

Unplug the transformer or switch off the power before cleaning or working on any fixture.

  • Clean every lens. This is the job that makes the biggest difference. A fixture with a dirty lens can lose a lot of its output, and ground-level and well lights fill with dirt fastest.
  • Wipe with a soft cloth and water, or a mild dish soap. Avoid abrasives and solvents, which craze acrylic and cloud glass. Hard-water spots from sprinklers come off with diluted vinegar.
  • Check the aim of every stake and adjustable fixture. Mowers, dogs, kids, wind and frost heave all move them.
  • Clear leaves, mulch and soil from around ground-level and in-ground fixtures.
  • Check wire entries and seals for damage, and look for any sign of water inside a lens.
  • Firm up stakes that have worked loose, and rebury wire that has worked up to the surface.

Seasonal jobs

  • Fall: the important one. Clean everything before the long nights, clear leaves off ground-level fixtures weekly while the trees drop, and check your timers after daylight saving time ends.
  • Winter: in snowy regions, mark in-ground fixtures before the first plowing and keep them clear of snow and ice-melt salt; check string-light anchors before winter storms and take down long spans.
  • Spring: the main clean and re-aim. Plants have changed since fall and several fixtures will now be shining into a shrub.
  • Summer: cut back plants that have grown across a fixture or a sensor, and re-aim anything the growth has swallowed. Check sprinklers are not soaking fixtures all summer.
  • Check tree-mounted fixtures and their straps every year and loosen them as the tree grows.
  • Look at the yard from inside once a year. The view from the window is what changes most as plants mature.

Pond and fountain fixtures

  • Unplug or switch off the power before putting your hands in the water, every time, without exception.
  • Underwater fixtures need cleaning far more often than anything else. Algae and mineral scale film the lens within weeks in summer.
  • Check the seal and the wire entry whenever you clean one. Water inside an underwater fixture is a failure, not a nuisance.
  • Never run an underwater fixture out of the water, even briefly, unless it is rated for it. Many rely on the water to keep cool.
  • Any fault in a pond or fountain installation on 120V is a job for a licensed electrician, not a repair to attempt.
  • See lighting near water.

Lifespan and replacement

  • Good solid brass, copper or stainless low-voltage fixtures last 10 to 20 years or more; cheap plastic and painted aluminum ones often fail within two or three winters.
  • LED fixtures dim gradually rather than dying outright, and cheap ones can shift color, so a system may need refreshing before anything has actually stopped working.
  • Replaceable LED bulbs are worth paying for. A sealed integrated LED means the whole fixture is disposable when it fades.
  • Solar lights usually fail at the battery first, typically after two to four years. Models with a replaceable battery last far longer.
  • Buy from a fixture line you can add to, and keep a spare if a line is being discontinued.
  • Keep any permit paperwork and your wire-route sketch together. You will want both.
Diagnosis

Eight problems and what is causing them

Match the symptom to the cause. Anything involving 120V house wiring is a job for a licensed electrician rather than a DIY fix.

Common landscape lighting problems, their usual causes and first steps.
SymptomMost likely causeWhat to do
Fixtures dim at the far end of a runVoltage drop on a long or overloaded 12V runShorten the run, use heavier gauge wire, feed it from the middle, use a higher voltage tap, or split it into two runs
One fixture has stopped workingWater inside, a failed splice, or an LED bulb at the end of its lifeUnplug, check the connection and the lens seal; replace the bulb if it is replaceable
Several fixtures out on one runA failed splice or damaged wire upstream of themWork back along the run from the first dead fixture to the last working one
Everything on the system is outTransformer failure, a tripped GFCI, or a timer or photocell problemCheck the GFCI outlet and press RESET; check the transformer's own breaker and timer. A GFCI that keeps tripping is a fault: get it checked
Lights noticeably dimmer than they used to beDirty lenses, or LED output declining with ageClean every lens first. It brings back more than people expect
Motion light triggering all nightSpider or web on the lens, moving plants, a heat source, or too wide a zoneWipe the lens, then narrow the zone and lower the sensitivity
Lights coming on at the wrong time in fall or springA fixed-clock timer rather than an astronomical one, or a daylight saving changeSwitch to an astronomical timer or a photocell, or reset the times after each clock change
Water visible inside a lensA failed seal, a damaged wire entry, or a fixture not rated for where it sitsUnplug and replace the fixture; make sure it is listed for wet or in-ground use as needed
The routine

Landscape lighting through the year

Two proper sessions and a few seasonal checks are the whole routine. Timing depends on your climate: a fall leaf cleanup is late October in zone 5 but December in zone 8, and in frost-free zones 10 and up the year is mostly about plant growth and sprinklers.

Spring

After your last frost

The main clean and re-aim, after winter and before the growth takes off (roughly March in the South, May in the northern tier).

  • Switch off, then clean every lens. The single most effective job.
  • Re-aim every adjustable fixture; several will be pointing at nothing.
  • Check wire entries and seals for damage.
  • Firm up stakes and rebury any wire that has worked up to the surface.
  • Check timers after daylight saving time starts, or switch to an astronomical timer and stop adjusting.

Summer

The growing season

The quiet season, and the time to keep plants off the fixtures.

  • Cut back growth that has swallowed a fixture or blocked a sensor.
  • Clean underwater pond and fountain fixtures, which film up fastest in hot weather.
  • Add or move fixtures while evenings are long and the ground is easy to dig (call 811 first).
  • Check string-light anchors and guide-wire tension, especially before thunderstorm or hurricane season.
  • Enjoy it. This is the season the lighting was built for.

Fall

As the leaves drop

The most important season: what you do now decides how the lighting performs all winter.

  • Clean every lens before the long nights.
  • Clear leaves off ground-level and in-ground fixtures weekly while the trees drop.
  • Check timers after daylight saving time ends in early November.
  • Check tree-mounted fixtures and loosen the straps.
  • Look at the yard from inside and adjust. This is when the window view matters most.

Winter

After your first frost

Watching and storm checks. The lighting earns its keep now.

  • Check string lights and long spans before winter storms, and take down holiday or seasonal sets.
  • Mark in-ground fixtures before snow, keep them clear, and keep de-icing salt off fixtures and wire.
  • Note anything not working for the spring list rather than digging in frozen or soggy ground.
  • Notice what the yard actually looks like from the kitchen window on a January evening.
  • Avoid working on outdoor electrics in the wet. Switch off first, and leave 120V faults to a licensed electrician.
Avoid these

Six control and maintenance mistakes

None of these is dramatic, and all six are why lighting stops getting used.

1. One switch for the whole yard

Tying every fixture to one switch means the deck lights, the path lights and the accent lights all come on together, and the system ends up either fully on or fully off, usually off.

The fixSplit it into three or four zones grouped by when you want them on: every night, when you are outside, and only when something moves. Plan the zones before the wire goes in.

2. Fixed-clock timers

A timer set in June comes on two hours after dark by October, and every daylight saving change knocks it out by another hour, so people stop trusting it and switch to manual.

The fixUse an astronomical timer, or a smart plug or transformer that schedules from sunset. It works out sunset for your location and date and needs no adjusting all year.

3. Everything on dusk-to-dawn

Lighting that burns from dusk to dawn costs several times as much to run, bothers neighbors and wildlife all night, and makes no difference to anyone using the yard.

The fixRun the decorative and accent lights from dusk until a sensible hour (10 or 11pm suits most households), and keep only porch and safety lighting on longer.

4. Never cleaning the lenses

A dirty lens loses a surprising amount of light, and the system dims so gradually that people decide the fixtures are failing and buy new ones.

The fixSwitch off and clean every lens twice a year, spring and fall, with a soft cloth and water. It is the most valuable twenty minutes in the whole routine.

5. Leaving sensors as they came out of the box

Motion sensors come set far too wide and far too sensitive, so they fire at cats, cars and swaying branches, and then get switched off for good.

The fixAim across the approach rather than down it, use the masking shields, narrow the zone, lower the sensitivity, and set a short on-time of a minute or two.

6. Working on lights with the power on

Cleaning a fixture, changing a bulb or handling a pond light with the power on is a real hazard, and outdoors in the wet it is worse.

The fixUnplug the transformer or switch off the power before touching any fixture, every time. Leave anything involving 120V house wiring, and any fault in a pond or fountain installation, to a licensed electrician.

Print it or check it off as you go

The controls and maintenance checklist

Fourteen jobs across the year. Your checks are saved in this browser only.

Controls

Sensors

Maintenance

Questions

Landscape lighting controls and upkeep: your questions answered

Answers to the questions homeowners ask most.

What is the best timer for landscape lighting?

An astronomical timer, or a smart plug or transformer that schedules from sunset, on the main zones. Unlike a fixed-clock timer it works out sunset for your location and date, so the lights come on at dusk all year, through daylight saving changes, with no adjusting, and off at whatever time you choose. Add a photocell or astronomical timer on porch lighting, a motion sensor on security lighting, and a switch or smart plug on the deck lighting you want on demand, and keep those on separate zones.

Should landscape lights be on a timer or a motion sensor?

Both, on different zones. Timers suit anything decorative or along a route that you want on through the evening: path lights, accent lights, string lights. Motion sensors suit security and occasional-use lighting, such as the side yard, the walk to the trash cans or the gate, where you only want light when something moves. Do not put them on the same control, or a security floodlight will keep firing while you are sitting outside.

Why does my motion sensor light keep coming on for no reason?

Check the lens first: a spider sitting on it or a web across it is by far the most common cause and takes ten seconds to fix. After that, the usual culprits are a zone set far too wide (catching cars, the sidewalk or a neighbor), plants moving in the beam, a heat source such as a dryer vent or an AC unit, animals like cats, raccoons and deer, or the light shining back on the sensor. Aim it across the approach rather than down it, use the masking shields, narrow the range and lower the sensitivity.

How often should I clean landscape lights?

Twice a year, spring and fall, and the fall cleaning matters most because it sets the system up for the long nights. Switch off the power first, then wipe every lens with a soft cloth and water or mild dish soap, with no abrasives or solvents; diluted vinegar removes sprinkler hard-water spots. Ground-level and in-ground lights fill with dirt fastest and need leaves cleared all through the fall. Underwater pond and fountain lights need cleaning far more often, sometimes monthly in summer, because algae films the lens within weeks.

Why have my landscape lights gotten dimmer?

Clean the lenses before assuming anything is failing. A dirty lens loses a surprising amount of light, and the change is so gradual that people decide the fixtures are worn out. If cleaning does not bring them back and only some fixtures are affected, the cause is usually voltage drop on a long or overloaded 12V run. If the whole system has dimmed evenly over several years, that is normal LED aging and the fixtures are reaching the end of their useful life.

Are smart landscape lights worth it?

A weatherproof outdoor smart plug, or a transformer with app control, is well worth it: it gives you sunset scheduling, remote and voice control and simple scenes with no wiring, and one per zone lets you build zones. Fully smart individual fixtures are more of a judgment call. Dimming is the useful feature, color changing is mostly a holiday novelty, Wi-Fi at the back of the lot is often the limit, and products get discontinued. Whatever you use, keep a manual override that works when the network does not.

How long do landscape lights last?

Good solid brass, copper or stainless low-voltage fixtures can last ten to twenty years or more; cheap plastic and painted aluminum ones often fail within two or three winters. LEDs generally dim gradually rather than dying outright, and cheap ones can shift color, so a system often needs refreshing before anything has actually stopped. Solar lights usually fail at the battery first, after two to four years, and models with a replaceable battery last far longer. Replaceable LED bulbs are worth paying for.

One of my landscape lights stopped working. What should I check?

Unplug the transformer first. If it is a single 12V fixture, check the splice and the lens seal for water, and replace the bulb if it is replaceable. If several on a run are out, work back from the first dead fixture to the last working one, because the fault is between them. If everything is out, check the GFCI outlet (press RESET), the transformer's own breaker and the timer or photocell. Anything involving 120V house wiring, a GFCI that keeps tripping, or a fault in a pond or fountain installation is a job for a licensed electrician.

Where to go from here

The rest of the section