Patios · FAQs

Patio FAQs: Straight Answers for US Homeowners

The patio questions that come up in backyards from Minnesota to Texas, answered briefly: where and how big, pavers or concrete, how deep the gravel base goes, which way it slopes, what frost does to it, and how to keep it clean. Type a word in the box to filter, or browse by section. Every answer points to the full guide.

General guidance for typical US backyards. Soil, climate and local codes vary, so read the full guides for the detail and check locally before you build. Part of the PlantMapper Patios section.

A landscaper setting stone pavers in a backyard on a rainy day
The patio questions people ask most, all on one page · photograph via Pexels
84 questions

Search the patio questions

Start typing and the list shrinks as you go. Try "base", "frost", "polymeric", "sealing", "efflorescence" or "permit". Clear the box to bring everything back.

Section one

Choosing and planning a patio

How big should a patio be?

Work from the furniture, not a round number. Take the table, add about 3 ft behind every chair, then add a walkway along at least two sides. A table for six usually needs around 12 × 10 ft at the very least and closer to 14 × 12 ft to feel easy. Add a grill station and you want another 5 to 6 ft. The sizing table is in Planning a Patio.

Which direction should a patio face?

It depends on your climate more than on a rule. Up north, a south- or west-facing patio catches the sun you want in spring and fall. In the South and Southwest, a west-facing slab can be unbearable on a summer afternoon, so an east-facing spot, the shade of a tree or a pergola is worth a lot. Sit in the spot at the times you would really use it before you commit.

Does the patio have to be next to the house?

No. Being close to the kitchen is handy for carrying food out, but if the back door faces into all-day shade or full afternoon sun, a second seating area out in the yard may get far more use. A small landing at the door plus a larger patio where conditions suit you often beats one compromise.

How much of the yard should the patio take?

In a typical suburban backyard a patio covering roughly a quarter to a third of the space feels generous without swallowing the lawn. In a small city lot or townhouse yard it is perfectly reasonable for the paving to cover almost everything, with beds and containers around the edge.

How much space do I need behind a dining chair?

About 30 in is the bare minimum to pull a chair out and sit down. Allow 36 to 42 in if people need to walk behind seated guests. Check the ends of the table too, because those are the chairs that end up with one leg off the edge.

Should the patio be square to the house or set at an angle?

Lining it up with the house is simple to lay out, looks calm and costs least. A patio or paver pattern turned 45 degrees can make a narrow yard feel wider, but every edge paver has to be cut, so labor and waste both go up.

Can I make a small patio look bigger?

Use larger, lighter pavers in a simple pattern with narrow joints, run the paving right to the fence or beds, grow things upward on trellis or the fence, and choose two or three big containers rather than a crowd of small pots. Fewer lines on the ground reads as more room.

When is the best time of year to build a patio?

Late spring through early fall in most of the country, once the ground has thawed and dried. Concrete and polymeric sand both need temperatures above about 40 to 50°F while they cure, and frozen or soggy soil compacts badly. In the Deep South and Southwest you can build most of the year, though midsummer heat is hard on crews and on fresh concrete. Good contractors book up early in spring.

What should I check before work starts?

Call 811 a few days before any digging so buried utility lines are marked; it is free. Then check access for a skid steer and pallet deliveries, where the dug-out soil will go, how the soil behaves in a test hole, whether you need a permit or HOA approval, and look at real samples of the pavers. The full list is in Planning a Patio.

Should I run conduit for lights and power under the patio?

Yes, even if you have no plans yet. A length of PVC conduit laid under the base before the pavers go down costs a few dollars; getting a wire under a finished patio later costs a great deal. Low-voltage landscape lighting is a DIY job, but line-voltage wiring and outlets should be installed by a licensed electrician and may need a permit.

Section two

Patio materials

What is the best material for a patio?

There is no single best. Concrete pavers are the all-rounder and handle freeze-thaw well, poured concrete is the budget choice, flagstone gives a natural look, brick suits older homes, and porcelain is the lowest-maintenance surface. Your climate, the style of the house and how much upkeep you want narrow it fast; the comparison table in Patio Materials takes about a minute.

Pavers or poured concrete: which is better?

Poured concrete usually costs less up front and is fast to install, but it will crack sooner or later, and repairs show. Pavers cost more but flex with frost and settling, and a damaged or stained paver can be lifted and replaced. In cold regions with frost heave, or anywhere you may need to dig under the patio later, pavers are usually the better long-term buy.

Is stamped concrete a good idea?

It can look convincing and costs less than real stone, but it is still a slab: it will crack, the color can wear in traffic areas, and it needs resealing every two to three years to stay looking right. It can also be slick when sealed and wet unless an anti-slip additive is used. Repairs are hard to color-match.

Which patio surface is least slippery?

Textured concrete pavers, natural-cleft flagstone, broom-finished concrete and outdoor porcelain rated for exterior use all grip well. Smooth sealed concrete and polished stone are the slippery ones. For porcelain, check the published wet slip rating (DCOF) and choose a textured outdoor finish. Algae and wet leaves cause more slips than any material.

Smooth or textured surface?

Smoother where the dining table sits, textured where people walk, especially on steps and in snowy areas. Flat surfaces keep chairs steady and are easy to sweep; textured ones grip better and hide dirt but make furniture rock.

Light or dark pavers?

In sunny, hot climates choose lighter colors: dark pavers and dark stamped concrete can get too hot for bare feet and pets. Light colors also brighten shady yards but show every stain. Dark tones hide everyday dirt and look modern. Mid-tone blends are the safe pick for most homes.

Large pavers or small ones?

The more curves and corners, the smaller the unit should be. Large-format pavers and slabs suit simple rectangles and lay quickly; brick-size pavers and small cobbles handle curves without lots of cutting and are easy to repair one at a time.

How thick should patio pavers be?

Concrete pavers are usually 2⅜ in for patios and walkways; 3⅛ in is for driveways. Flagstone for a sand-set patio should be at least 1½ to 2 in thick; thinner flagstone needs a concrete slab under it. Outdoor porcelain is about ¾ in thick. Solid, even support underneath matters more than thickness.

What is the difference between flagstone and pavers?

Flagstone is natural stone, such as bluestone, sandstone, limestone or slate, split into irregular or cut pieces that vary in thickness. Pavers are manufactured units, usually concrete or clay brick, made to an exact size and thickness. Pavers are quicker and easier to lay level; flagstone takes more skill but has a look that pavers imitate.

Can I use indoor tile outside?

No. Indoor tile is not made to survive freezing and thawing, and its surface is slippery when wet. Use porcelain sold specifically for exterior use, which is denser, frost resistant and has a textured, slip-resistant finish.

Which material works best in shade?

Dense surfaces that do not stay damp: outdoor porcelain first, then good-quality concrete pavers or granite. In humid regions like the Southeast and Pacific Northwest, porous stone and brick in shade turn green and slick quickly and need cleaning every year.

Will my pavers fade?

Clay brick and porcelain hold their color because it is fired in. Natural stone weathers gently, which most people like. Colored concrete pavers and stamped concrete are the ones that fade, especially in strong Southwest and mountain sun; better pavers color the whole unit, and sealing slows fading.

Can I mix two patio materials?

Yes, and it often looks better. Let one material dominate and use the second as a clear accent, such as a brick or paver border around poured concrete, or a band of darker pavers. Two materials fighting over the same area rarely looks good.

How many extra pavers should I order?

Add about 5 to 10% for a simple rectangle and 10 to 15% for curves, diagonals or herringbone. Buy everything from the same production run, and keep a few spares in the garage for future repairs. The Patio Area Calculator adds the waste allowance for you.

Section three

Building a patio

How deep should the gravel base be for a paver patio?

For a walk-on patio, 4 to 6 in of compacted crushed-stone base is the usual figure on firm, well-drained soil. On clay, wet ground or in cold regions with deep frost, many installers go to 6 to 8 in or more. Driveways are a different build. The number that counts is the depth after compaction, done in 2 to 3 in layers.

How deep do I need to dig for a patio?

Add up the paver thickness, about 1 in of bedding sand and the compacted base depth, all measured down from the finished surface. For 2⅜ in pavers on 1 in of sand over 6 in of base, that is roughly 9 to 10 in. Work it out for your own materials and allow for the slope.

What gravel goes under pavers?

Crushed, angular stone with a range of sizes from about ¾ in down to dust, sold as paver base, road base, crusher run, "¾ minus" or Class II base depending on the region. The angular pieces lock together under a plate compactor and the fines fill the gaps. Rounded pea gravel rolls and will never form a firm base.

Can you lay pavers directly on dirt?

No. Soil holds organic matter that rots, swells and shrinks with moisture and heaves when it freezes, so pavers laid on it sink and rock within a season or two. The only real exception is stepping stones set into a lawn.

What sand goes under pavers?

Coarse, washed concrete sand (ASTM C33), screeded to an even 1 in over the compacted base. It should be loose and level, not compacted before the pavers go down. Do not use play sand, mason sand or stone dust as the bedding layer, and do not use polymeric sand under the pavers: it belongs only in the joints.

How do I set flagstone on concrete?

Thin flagstone over an existing sound slab is set in a full bed of mortar, typically a Type S mix about ¾ to 1 in thick, with the joints then grouted with mortar. The slab underneath must be solid and sloped correctly, because the stone will follow every crack in it.

Why do people skimp on the base?

Because nobody sees it once the pavers are down, and digging out and hauling away soil is the slowest, heaviest part of the job. It is also the most common reason a patio sinks, rocks or heaves within a few years. A thin base with no compaction looks fine on day one and fails later.

Do I need edge restraint around pavers?

Yes. Without a rigid edge the outer pavers creep outward, the joints open and the whole field loosens. Use plastic or aluminum paver edging spiked into the base, a concrete curb or a soldier course of pavers set in concrete. The base should extend past the edge so the restraint sits on gravel, not soil.

What is polymeric sand and should I use it?

Polymeric sand is joint sand mixed with a binder that hardens when wetted. It resists washing out, ants and weeds much better than plain sand. Sweep it into completely dry pavers, compact it down, blow every grain off the surface, then mist it as the bag directs. Leftover haze on the surface is hard to remove.

Why is my polymeric sand not hardening?

Usually too little water, too much water that washed the binder out, joints that were not filled to full depth, damp pavers or a damp base when it went in, rain soon after, or temperatures too low. Most products need dry weather for a day and temperatures above about 40°F. Badly cured joints have to be cleaned out and redone.

How long before I can use a new patio?

A paver patio can usually be walked on as soon as it is compacted, but keep water and heavy furniture off fresh polymeric sand for the time on the bag, often 24 to 48 hours. Poured concrete can take foot traffic after a day or two, furniture after about a week, and reaches most of its strength in about 28 days.

Can I build a patio in winter?

Not in cold regions. Never compact a base on frozen ground or pour concrete onto it, and most polymeric sands and mortars need temperatures above about 40°F and rising. Concrete poured in the cold needs blankets and special mixes. In zones 9 and warmer, winter is often the most pleasant time to build.

Do I need landscape fabric under a patio?

On clay or soft ground, a woven geotextile between the soil and the gravel base is well worth it, because it stops the two layers mixing and the base sinking. It does not stop weeds in the joints, which grow from seeds landing on top, so do not buy it for that reason.

Can you put pavers over an old concrete patio?

Sometimes. The old slab must be sound, not heaving, and already sloped away from the house, and the extra height of thin overlay pavers plus bedding must still leave the surface below the door threshold and the siding. Cracks in the slab will show through. See the full answer.

How do I cut pavers safely?

Use a wet saw or a cut-off saw with a diamond blade and water feed, outdoors, with eye and hearing protection and a proper respirator. Dry-cutting concrete, stone and porcelain makes crystalline silica dust, which causes permanent lung disease. A splitter or chisel makes dust-free cuts on standard pavers.

Should the base be wider than the patio?

Yes. Extend the compacted base about 6 in beyond the finished edge, or as far as the base is deep, so the edge pavers and the edge restraint sit on solid ground. Unsupported edges are where patios drop first.

Can I build a paver patio myself?

A simple rectangle on firm, fairly level ground, up to about 150 to 200 sq ft, is a doable project if you rent a plate compactor and accept that digging is most of the work. Patios against the house where grading is tight, retaining walls, poor drainage and large-format porcelain are where a pro earns the fee.

Section four

Drainage and slope

Does a patio need drainage?

Every patio needs a plan for the water, but not every patio needs a drain. A patio sloping gently onto a lawn or planting bed that soaks up the runoff is properly drained. What no patio can be is dead flat, or tilted toward the house.

Which way should a patio slope?

Away from the house, toward a place that can take the water. Never toward the foundation, a door or a neighbor's yard. If the yard naturally falls toward the house, the patio still slopes away, and a channel drain or swale catches the water at the low point.

How much slope should a patio have?

About ⅛ to ¼ in per foot, so a 12 ft patio drops roughly 1½ to 3 in from the house to the far edge. Textured surfaces like flagstone like the steeper end. Build the slope into the compacted base, not by thickening the sand.

How much water does a patio shed?

More than you might think. One inch of rain on a 300 sq ft patio is about 190 gallons, and a summer thunderstorm can drop that in under an hour. Work out your own figure before deciding it can all run into one flower bed.

Where should patio water drain to?

A lawn or bed that can absorb it, a gravel strip, a rain garden, or a channel drain piped to a dry well or a daylight outlet lower in the yard. Not toward the foundation, not onto a neighbor's property, and not into the sanitary sewer. Some towns also limit piping runoff to the street or storm drain, so check locally.

What is a channel drain for?

A channel (trench) drain catches water along a line rather than at one point, which helps where the patio meets the house, a garage or a step down. It only collects water; the pipe from it still has to run somewhere the water can go.

Will a dry well work in my yard?

Test first. Dig a hole about 1 to 2 ft deep, fill it with water, let it drain, then fill it again and time it. If the water drops 1 in or more an hour, a dry well can work; if it is still standing the next day, it will not. Heavy clay, caliche, shallow bedrock and high water tables all defeat dry wells.

How far from the house should a dry well be?

At least 10 ft from the foundation is a common rule of thumb, and further on clay or where the ground slopes back toward the house. Keep it away from septic fields and property lines, and check whether your town has its own setback rules.

How far below the door should the patio be?

Leave a step down of at least an inch or two below the door threshold, and more is better; building codes generally require a landing at an exterior door within a set distance below the threshold, so check locally. The patio also must not bury the bottom of the siding: many siding makers want several inches of clearance above hard surfaces.

Can the patio be level with the back door?

A flush, no-step threshold is possible, but only with a door rated for it, a properly sized trench drain right outside, and paving that still slopes away. It is not a detail to improvise, because water driven against the door ends up in the subfloor.

Are permeable pavers worth it?

Often, especially where runoff is a problem or a town limits impervious surface on a lot. Some places offer stormwater fee credits or rebates for them. They are a full system, though: open-graded stone base, small chip stone in the joints instead of sand, and a deeper excavation, so they cost more.

What do I do about a patio on heavy clay?

Expect the soil to absorb very little, so plan to move the water away instead: a good slope to a channel drain or swale, piped to daylight downhill. Use a deeper base with a geotextile under it, and a gravel strip along the low edge to spread the runoff. Clay also swells and shrinks, which a thicker base helps to ride out.

Section five

Patio problems

Why are my pavers sinking or rocking?

Almost always the base: too thin, poorly compacted, built on soft soil, or the bedding sand washed out through open joints or past a missing edge restraint. The fix is to lift the pavers, correct the base and sand, relay and re-sand. Pounding them down harder does nothing.

Why is water puddling on my patio?

Not enough slope, slope that runs into a dead end, a sunken patch, or a clogged drain. Pour a couple of buckets across it: one lingering puddle means a local dip; water that will not move anywhere means the whole patio is too flat. See Patio Problems.

What is frost heave and how do I stop it?

Water in the soil freezes into ice lenses that push the ground up, then it settles back unevenly in the thaw. It is a real issue in the Northeast, Midwest, Plains and mountain states and rarely matters in the Deep South. Prevent it with a thicker, free-draining crushed-stone base, good slope and drainage, and pavers rather than a rigid slab, which tends to crack instead.

Can I just re-sand a patio with loose pavers?

Not if they rock. Joint sand locks pavers together but cannot fill a hollow underneath. Lift the moving pavers, fix the base and bedding, relay them, then re-sand the area.

How do I stop weeds between pavers?

Weeds in paver joints grow from seeds and dirt that settle in from above, not from the soil below. Pull or scrape them out, refill the joints to full depth with polymeric sand, and sweep a few times a season so debris never builds up.

Why is my patio slippery?

Usually algae or a film of organic grime, especially in shade and humid weather, rather than the material. Clean it off with an algae and moss cleaner, then tackle the dampness. If it is slippery when clean and dry, the surface or the sealer on it may be too smooth for outdoor use.

Why did my concrete patio crack?

Concrete shrinks as it cures and moves with temperature, so some cracking is normal; control joints are cut to make it crack in straight lines where you want. Wide, uneven or growing cracks point to a poor base, missing joints, frost heave, expansive clay or tree roots. Fine cracks can be sealed; a heaving slab usually has to be replaced or mudjacked.

What is the white haze on my new pavers?

Efflorescence: natural salts carried to the surface as moisture leaves the concrete. It is very common on new concrete pavers and stamped concrete, it is not a defect, and it usually weathers away within a few months to a year. If it persists, use a cleaner made for efflorescence, and never seal over it.

Can freeze-thaw damage be repaired?

Scaling, flaking and spalling on concrete and pavers is permanent. Damaged pavers can be swapped out; concrete may be resurfaced, but the finish rarely matches. Stop the damage by improving drainage, sealing concrete in freeze-thaw areas, and avoiding rock salt and ammonium-based de-icers.

How do I remove rust stains from pavers?

Stains from patio furniture, tools or fertilizer granules often lift with a rust remover made for concrete or stone. Test it in a hidden corner first, and avoid acidic products on limestone or marble. Rust spots from iron in some natural stone are part of the stone and usually cannot be removed.

My patio is sending water into the basement or crawl space. What now?

Act quickly. The likely cause is a patio that has settled toward the house, so water runs to the foundation instead of away. Have a contractor check the slope and the joint between the patio and the wall; the fix may be relaying, a drain along the house, or regrading. This is one of the few patio faults that damages the house itself.

Should I repair or replace an old patio?

Repair when the problems are in one area and the overall slope is right. Replace when the whole patio is too flat or tilts toward the house, sinking is widespread, several problems overlap, or matching pavers are no longer made. If repairs keep failing within a year or two, the base is the real problem.

Section six

Cleaning, sealing and care

How do you clean a patio without damaging it?

Sweep, wet the surface, apply a cleaner suited to the material, leave it for the time on the label, scrub with a stiff brush along the joints and rinse until the water runs clear. Work in sections, avoid hot midday sun, and test any new product in an out-of-sight corner first.

Can you power wash pavers?

Yes, carefully. Use a 25 or 40 degree fan tip, keep the wand a foot or so away at a low angle and keep it moving, and do not aim into the joints. A rotary surface-cleaner attachment gives a much more even result. Go gentle on soft stone and sealed surfaces, and expect to re-sand the joints afterward.

Should I seal my pavers or concrete patio?

Often worth it, not essential. A good sealer helps concrete and pavers resist stains, freeze-thaw and de-icer damage, slows fading and can lock joint sand in place. Porcelain does not need it. Wait until efflorescence has cleared and the surface is clean and dry, use a breathable product, and expect to reseal every two to five years.

How often should I clean my patio?

Sweep or blow it off every week or two in leaf season, wash it properly in spring and fall, and deep clean every few years. Regular light care beats a three-year gap followed by an aggressive power wash.

How do I get moss off a patio?

Scrape the bulk out of the joints, then treat what is left with a moss and algae cleaner. Then fix the cause: shade, poor slope, wet joints and fallen leaves. Moss is mainly a problem in damp, shady yards in the Pacific Northwest, the Northeast and the humid South.

What kills algae on pavers?

An outdoor algae, mold and mildew cleaner made for hard surfaces, applied to a swept patio and left for as long as the label says. Some work over days or weeks with rain rather than in minutes. Bleach streaks colored concrete and harms nearby plants, and the green comes back if the patio stays damp.

How do I get grease stains off a patio?

Speed matters most. Blot fresh grease from the grill, cover it with cat litter or another absorbent, then scrub with a degreaser made for concrete or pavers. For older stains soaked into concrete or stone, a poultice left for several hours draws out more than harder scrubbing. Badly stained pavers can simply be flipped or replaced. More in Patio Maintenance.

What is the lowest-maintenance patio material?

Outdoor porcelain, by a distance: no sealing, no fading and very little staining. Granite and good concrete pavers come next. Light limestone and soft stone in shade, and stamped concrete that needs regular resealing, ask the most of you.

Do I need to re-sand my pavers?

Yes, whenever the joints look low or open, and always after power washing. Use polymeric sand or dry jointing sand, sweep it in only when the pavers are bone dry, run a plate compactor over pavers or tap them so it settles, and top up until the joints are full.

What de-icer is safe for pavers and concrete?

Use as little as possible of any de-icer. Calcium chloride and calcium magnesium acetate (CMA) are gentler on concrete and plants than rock salt; avoid ammonium nitrate and ammonium sulfate, which attack concrete. Do not use any de-icer on concrete in its first winter. Shovel before snow packs down, and use sand for traction.

Why does my patio turn green every year?

Because it stays damp. Shade, humidity, poor slope and leaves left lying are perfect for algae, particularly in the Southeast and the Pacific Northwest. Cleaning removes it; more sun and air, better slope and regular sweeping keep it away.

How long should a patio last?

A well-built paver or flagstone patio can last 25 to 50 years or more, with odd pavers replaced along the way. Poured concrete commonly lasts 25 to 30 years or more, stamped concrete similar with regular resealing. What cuts life short is the base, drainage and frost, not the surface.

Section seven

Cost, permits and rules

Do I need a permit for a patio?

Often not for a ground-level paver or concrete patio, but it varies by city and county, so check locally. Permits are more likely for raised patios, retaining walls, patio covers, electrical work, or where your town limits impervious surface or setbacks from property lines. If you have an HOA, get approval in writing before you start.

How much does a patio cost per square foot?

Rough installed ranges, which vary widely by region and site: plain poured concrete about $6 to $15 per sq ft, stamped concrete about $12 to $25, concrete pavers about $12 to $30, flagstone about $15 to $35 and porcelain about $20 to $40 or more. DIY materials cost a fraction of that. Get local quotes before you budget.

What makes one patio quote much cheaper than another?

Usually something hidden: a thinner base, no compaction in layers, no edge restraint, or no plan for the water. Ask every contractor to write down the excavation depth, the base material and compacted depth, the bedding, the joint sand, the edging and where the runoff will go.

Where does the money go on a patio?

Labor is usually the biggest share, then the pavers or stone, then excavation and hauling away soil, the gravel base, drainage, edging and any steps or walls. Tight access with no room for a skid steer, and curves or multiple levels, push labor up more than most people expect.

Is it cheaper to extend an existing patio?

Sometimes, but matching weathered pavers or old concrete is close to impossible, and you inherit the old slope and any problems at the seam. An extension in a deliberately different, complementary material with a clear border usually looks better than a near-miss match.

Where should I save money if the budget is tight?

On size, not on the build. A smaller patio in decent material on a proper base beats a big one in bargain pavers on a thin base, because the base is the one part you can never upgrade later without tearing everything up. You can add on later.

Do I need HOA approval for a patio?

If you live in an HOA, very likely. Many associations require approval for any hardscape, and may set rules on materials, colors, size and drainage. Submit the plan before you sign with a contractor; building without approval can mean fines or being told to remove it.

Read the detail

The full Patios guides

Each answer above is covered in depth in one of these.

The small print

Notes and limitations

Short answers, longer guides

These answers are kept short on purpose. Each one is explained in full, with the caveats and site details, in the guide it links to.

No one build suits every yard

The depths, slopes and figures here describe common US practice for an ordinary backyard patio. Soil type, frost depth in your region, the material and the drainage all change what is needed.

The house, walls and drainage

Anything that affects the foundation, a door threshold, the siding, a retaining wall or a drain connection should be looked at on site by a qualified contractor.

Permits and HOAs

Permit rules are set by your city or county and HOA rules by your association, and both change over time. Check with your local building department and HOA before you build, and call 811 before you dig. Nothing here is legal advice.

Products

Cleaners, sealers, de-icers and joint sands all come with their own instructions. The manufacturer’s directions take priority over anything on this page.

Affiliate links

Some links elsewhere in this section are Amazon affiliate links. PlantMapper may earn a commission from qualifying purchases at no extra cost to you. See our affiliate disclosure.